6ES5 482-7LF11

Siemens 6ES5 482-7LF11 – S5 Digital I/O Module, 16 Readback Inputs and 16 P-Switching Outputs

Siemens 6ES5 482-7LF11 combines 16 inputs and 16 outputs in an isolated SIMATIC S5 module rated 24 V DC, 0.5 A per output. In S5-115F applications it provides M-reading feedback inputs and P-switching outputs. Inputs and outputs use optocoupler isolation in groups of eight.

Its distinguishing function is readback. The S5-115F manual specifies the 16 inputs for reading back 24 V safety-related outputs in the other subunit. When selecting S5 digital input/output modules, check this function alongside channel count, and confirm the CPU and system arrangement against the existing project.

Purpose of the M-reading inputs

M-reading describes activation by M potential. However, do not use these inputs for general sensor acquisition as though this were an ordinary digital input module. When reviewing PNP/NPN connections, first identify which output in which subunit is monitored by each readback connection.

Typical input current is 0.8 mA, with an input delay of 1.4–5 ms in both directions. Record the command bit, actual output voltage and readback bit together. If they disagree, examine the other subunit, shared reference and wiring as well as the card.

P-switching outputs and load limits

The 16 P-switching outputs switch the positive side of the load. Nominal load supply is 24 V DC, with a permissible range of 20–30 V. When selecting a digital output, check the steady current and pickup behaviour of the relay or contactor coil; assess more than its nameplate wattage against the 0.5 A limit.

A 50% load factor applies to total group current at 55°C. For example, eight outputs × 0.5 A gives 4 A; half of that is 2 A per group. Assess power supply capacity and panel temperature together, and retain the project's PELV supply arrangement.

Addressing and IM 306 setting

Inputs and outputs share the same numerical starting address. With IM 306 addressing, this card is treated as a 16-bit module: set the 16/32 selector to ON / 16 bit and use an even starting byte. Compare the PLC program addresses with the hardware setting on the rack.

For an example starting byte of 32 = 20h, the areas are I32.0–I33.7 and Q32.0–Q33.7. This is an addressing example. The card's 32 combined I/O points do not require one four-byte input area in the PLC.

Front connector and readback wiring

The front connection is 46-pole. ST 50 lists 6ES5 490-7LB21 for screw terminals. When inspecting S5 cables and connectors, compare terminal numbers, links and group references with the drawing. Check that the card and front connector are fully seated in the S5 rack.

The readback input wiring limit is 60 m unshielded or 100 m shielded. Keep these limits separate from the longer distances in the output cable table. Check grounding and reference connections, and measure DC voltage at the output and readback input connection points.

Differences between similar order numbers

6ES5 482-7LA11 provides general-purpose P-reading/P-switching I/O; 6ES5 482-7LF21 has P-reading feedback inputs and M-switching outputs. Do not treat other 482 suffixes, such as 6ES5 482-8MA12, as revisions of this card. Select replacements against the Siemens S5 system, complete order number and connection function.

Editor’s Note

Start with the 7LF11 suffix and the readback connections. “Sixteen inputs and sixteen outputs” is not enough to identify the right replacement. Compare readable photographs of both labels side by side.

Do not test these inputs by connecting arbitrary sensors. First locate the monitored output and its subunit in the drawing. If the output command is correct but feedback is missing, include wiring and reference connections in the investigation.

Photograph the IM 306 settings before removing the card. Seeing 32 combined points can lead to the wrong selector position: this module uses the 16-bit addressing setting. A photograph taken before removal can save a lengthy search later.

Do not finish after switching two unloaded outputs. Check every required channel with a suitable test load and its readback path. If the fault appears in a warm panel, calculate the total load of each eight-channel group; a successful cold workshop test is only part of the assessment.

For a used unit, specify the complete model, quantity, label photograph, working/faulty condition and price. Sales require an invoice; returns are not accepted, and workshop testing is available. To offer a card for sale, send its details to otomasyonavm@gmail.com.

OtomasyonAVM resources and PDFs

+ 6ES5 482-7LF11 model page and Second-hand SIMATIC S5 models.

+ Siemens S5-115 PDF archive. Use the technical data and readback drawings in the S5-115F manual, EWA 4NEB 811 6148-02, for this card.

+ S5 digital input/output range and S5 cables and connectors.

Related topics

+ 6ES5 482-7LA11 · 6ES5 482-7LF21.

+ 6ES5 482-8MA12 · 6ES5 482-8MA13. These links support model comparison; they do not establish direct interchangeability.

Browse SIMATIC S5

+ SIMATIC S5 · S5 digital inputs · S5 digital outputs.

+ S5 racks and carriers · Siemens second-hand range.

Siemens and external references

+ Siemens S5-115F Manual Volume 1/2, EWA 4NEB 811 6148-02 – English: printed 8-21 exact model data and input-use note; 8-23 wiring example; 5-4 IM 306 addressing.

+ Siemens SIMATIC S5 ST 50 catalogue, 1998 – English: 3/41 inputs; 3/42 outputs and connectors; 3/43 wiring diagrams.