6ES5 240-1AA11
Siemens SIMATIC S5 6ES5 240-1AA11 IP 240 counter module
The 6ES5 240-1AA11 is a Siemens IP 240 module for pulse counting in SIMATIC S5 systems. The two-channel IP 240 family is listed with the S5 positioning modules and covers pulse counting, position decoding and positioning.
In a feed mechanism, pulse signals can be used to track part counts or travel. When a machine derives position from shaft rotation, direction and reference signals from the incremental encoder also matter. The rotary encoder guide explains how these signals are generated.
Signals and connections
The IP 240 family manual describes CLK (count pulses) and GT (count gate) for counting, and A/B/Z signals for position decoding. Before replacing a card, record the active channel’s 5 V or 24 V input setting and whether the signal is single-ended or differential. For a line-driver encoder, check the signal pairs. For TTL or HTL, check the actual output level.
Compare the front plugs and cable shielding with the machine drawings. The S5 cables and connectors section helps identify the plug, while the encoder accessories section covers couplings and fittings that are worth checking when counts are inconsistent. Verify the pinout against the drawing for the card’s order number and hardware revision.
Rack, STEP 5 and card replacement
Record the S5 rack model, slot number and the order number of any S5 interface module in the installation. Check the rack and slot requirements separately for a system such as an S5-115U with CPU 944 or an S5 system with CPU 928.
Back up the STEP 5 project, including the module address, channel mode and the FBs and DBs in use. The Siemens family manual identifies FB 171 as the configuration block and FB 172 as the control and data-transfer block for counting. The IP 240 configuration package has a separate order number. Check the block version against the existing project before fitting a spare.
Siemens identifies the 6ES5 240-1AA21 as a replacement for the 6ES5 240-1AA11 and 6ES5 240-1AA12. For a change from 1AA11 to 1AA21, Siemens specifically points to Chapters 2–5 and 13 of the third-edition manual. Check the module address, input settings and connector wiring against those instructions.
Where the machine only counts pulses, the IP 242A counter module provides a point of comparison. A machine with an absolute encoder may use a different card, such as the IP 241 absolute encoder interface module. Identify the spare by the installed order number, operating mode and electrical interface.
Editor’s Note
For a used card, request a clear photo of the 1AA11 label and E-Stand (hardware revision) and close-ups of the front connectors. On the bench, apply a known pulse train at the appropriate level and test each channel separately. In counting mode, check the GT condition and the value read in STEP 5 together. If no count appears, start by checking the channel settings and connector pins.
Selling a 6ES5 240-1AA11? Send the label photo, quantity, working condition and asking price to otomasyonavm@gmail.com.
PDF archive
Related topics
S5 special modules · IP 242B high-speed counter module · IP 246 positioning module
Navigation
SIMATIC S5 · Used Siemens automation · Used automation equipment
References
Siemens IP 240 product information (German, EWA 4NEB 811 6123-10, p. 1). Conditions for replacing the 1AA11 with the 1AA21.
Siemens IP 240 family manual (English, 3rd edition, EWA 4NEB 811 6120-02b, Chs. 1–6, 8 and 13). This edition covers the 1AA21 and the 1AA12 with replacement pages.
Siemens migration guide from S5 to S7-1500 (German, document 105106251, p. 48, Table 7-9). Siemens lists the exact 1AA11 order number as an IP 240 counter module.