Teco VFD fault codes 3

TECO VFD Fault Codes 3

Warning and Self-Diagnostic Messages

When the inverter detects a warning, the warning code flashes on the keypad. A warning does not normally operate the fault relay, and the inverter can continue running.

When the warning condition disappears, the keypad returns to its normal display.

A self-diagnostic message is displayed when the inverter detects an invalid parameter setting or a conflict between parameters. The fault relay does not normally operate for this type of message, but the inverter will not accept a RUN command until the parameter problem has been corrected.

Warning and self-diagnostic codes normally flash on the keypad while the condition is active.

Voltage Warnings

OV (Flashing) – Overvoltage

Description: The DC bus voltage has exceeded the overvoltage detection level.

200 V class: approximately 410 VDC
400 V class: approximately 820 VDC

For the 440 V class, the source states that if input-voltage parameter 01-14 is set below 400 V, the OV detection level is reduced to approximately 700 VDC.

Possible causes:
- Deceleration time is too short.
- Regenerative energy from the motor is raising the DC bus voltage.
- Incoming supply voltage is too high.
- Power-factor correction capacitors are being used.
- Braking load is too high.
- Braking transistor or braking resistor is faulty.
- Speed-search parameters are incorrect.

Check:
- Increase the deceleration time.
- Check the incoming supply voltage.
- Use an AC input reactor where appropriate.
- Check for power-factor correction capacitors connected to the motor circuit.
- Check the braking resistor and braking transistor.
- Use a suitable braking unit where required.
- Check the speed-search settings.

UV (Flashing) – Undervoltage

Description: The DC bus voltage has fallen below the undervoltage detection level, or the pre-charge contactor is not active while the inverter is running.

200 V class: approximately 190 VDC
400 V class: approximately 380 VDC

The source also states that the detection value can be adjusted with parameter 07-13.

Possible causes:
- Incoming voltage too low.
- Input phase loss.
- Supply-voltage fluctuation.
- Pre-charge or magnetic contactor fault.
- Incorrect DC bus voltage feedback.

Check:
- Measure the incoming supply voltage.
- Check the input wiring and phases.
- Check the power source.
- Check the pre-charge contactor.
- If the supply is normal and the fault remains, inspect the control and power circuits.

Temperature Warnings

OH1 – Heatsink Overtemperature

Description: The inverter heatsink temperature is too high.

If this fault occurs three times within five minutes, the source specifies waiting approximately 10 minutes before resetting the fault.

Possible causes:
- Ambient temperature too high.
- Cooling fan stopped.
- Carrier-frequency setting too high.

Check:
- Check the ambient temperature around the inverter.
- Check the cooling fan.
- Check the heatsink for dust or blocked airflow.
- Check the carrier-frequency setting.

OH2 – Inverter Overtemperature Warning

Description: An external overtemperature warning has been received through a multifunction digital input.

Check:
- Check the multifunction input assignment.
- Check the external temperature-warning signal.
- Check the digital-input wiring.

Torque Detection

OT – Over-Torque Detection

Description: The inverter output torque has remained above the configured over-torque level for the specified time.

Check:
- Check the over-torque detection settings.
- Check parameters 08-15 / 08-16 where applicable.
- Reduce the mechanical load.
- Check the machine duty cycle.

UT – Under-Torque Detection

Description: The inverter output torque has remained below the configured under-torque level for the specified time.

Possible causes:
- Sudden loss of load.
- Broken belt.
- Mechanical coupling disconnected.

Check:
- Check the under-torque detection settings.
- Check parameters 08-19 / 08-20 where applicable.
- Check the belt, coupling and mechanical load.

External Base Block

bb1 / bb2 / bb3 / bb4 / bb5 – External Base Block

Description: An external Base Block command is active through the corresponding multifunction digital input.

Check:
- Check the multifunction digital-input assignment.
- Check the external Base Block signal.
- Check the input wiring.

Overload Faults

OL1 – Motor Overload

Description: The internal motor overload protection has tripped. The source states that the protection curve is active when parameter 08-05 is set to a value ending in xxx1.

Possible causes:
- V/f voltage setting too high, causing motor over-excitation.
- Incorrect motor rated-current setting at 02-01.
- Motor load too high.

Check:
- Check the V/f curve.
- Check parameter 02-01 against the motor nameplate current.
- Reduce the motor load.
- Check the machine duty cycle.

OL2 – Inverter Overload

Description: The inverter thermal overload protection has tripped.

If inverter overload occurs four times within five minutes, the source specifies waiting approximately four minutes before resetting the fault.

Possible causes:
- V/f voltage setting too high.
- Inverter rating too small for the application.
- Mechanical load too high.

Check:
- Check the V/f curve.
- Check the inverter output current.
- Reduce the motor load.
- Use a larger inverter if the application exceeds the present drive rating.

Communication Faults

CE – Communication Error

Description: No Modbus communication has been received for approximately 2 seconds. The source states that this fault is active when 09-07 = 3.

Check:
- Check the communication cable.
- Check the RS485 connections.
- Check whether the PLC, HMI or host computer is still transmitting.
- Check the communication software and parameters.

CF00 – Operator Communication Error 1

Description: Communication between the LCD operator and inverter cannot be established approximately 5 seconds after power-up.

Check:
- Disconnect and reconnect the LCD operator.
- Check the operator cable and connectors.
- If the fault remains, inspect the control board.

CF01 – Operator Communication Error 2

Description: Communication has been established, but data-transmission errors continue for more than approximately 2 seconds.

Check:
- Disconnect and reconnect the operator.
- Check the operator cable and connectors.
- If the fault remains, inspect the control board.

CF20 – Double Communication Error

Description: Profibus and Modbus communication mechanisms are configured for simultaneous redundant operation.

Check: Review the communication configuration and use only the communication method required by the application.

Input Voltage Monitoring

CT Fault – Three-Phase Input Voltage Fault

Description: An abnormal condition has been detected in the three-phase input-voltage monitoring circuit.

Possible causes:
- Abnormal input voltage.
- Excessive electrical noise.
- Control-board fault.

Check:
- Measure all three input phases.
- Check phase-to-phase voltage balance.
- Check the voltage-detection signal and control board.

TECO VFD Fault Code Pages

+ TECO VFD Fault Codes – Main Page

+ TECO VFD Fault Codes 2

+ TECO VFD Fault Codes 3

+ TECO VFD Fault Codes 4

Related TECO Pages

+ TECO Automation Main Page

+ TECO VFD Price List

+ TECO Contact

+ VFD Main Page