How does static electricity damage circuit boards?

How static electricity damages circuit boards

How static electricity damages circuit boards

A replacement board can be damaged before it is ever powered up. An ordinary plastic bag, an unsuitable workbench or a charged person touching a connector may provide the conditions for electrostatic discharge, or ESD. The discharge can drive a brief, intense current through structures inside a semiconductor. You do not have to feel a shock or see a spark for damage to occur.

On this page: Handling and storage · What gets damaged · Checking a suspect board

Prepare the work area before opening the package

Effective ESD control keeps people, work surfaces and suitable equipment at a controlled common potential. The aim is to prevent a sudden equalisation of charge through the board. A mat with an “antistatic” label is only one item in that arrangement; its properties, connections and condition must be suitable.

Ground the operator through the proper system. Use a wired ESD wrist strap that contacts the skin and has the manufacturer’s current-limiting arrangement. Verify its operation with an appropriate tester or continuous monitor. Touching metal once is not lasting protection: subsequent movement can charge you again. Do not improvise a grounding point from a neutral conductor, radiator or unidentified metalwork.

Control the surface and tools. Use a suitable static-dissipative mat with its intended connection, along with ESD-appropriate soldering and handling equipment. Keep ordinary plastic brushes, foam, bags and tape away from exposed boards. Grounding cannot reliably remove charge from an insulating surface; processes involving unavoidable insulators may need suitable ionisation. Higher humidity is not a substitute for a controlled workstation.

Keep electrical safety separate from ESD protection. A wrist strap does not protect its wearer against electric shock. These handling measures concern boards with power disconnected and stored energy safely removed. Power-stage capacitors can retain dangerous voltage after shutdown. Do not use a grounding wrist strap while working on exposed live mains or high-voltage circuits.

Handle and transport the board correctly. Hold it by the edges and avoid connector contacts and component leads. Edge handling supports ESD precautions; it does not replace them. Open protective packaging in the controlled work area. For transport outside that area, use suitable, closed ESD-shielding packaging. A low-charging bag and a discharge-shielding bag perform different functions. Colour and an “antistatic” label alone do not establish suitability.

Where the charge comes from—and where it goes

Walking, moving clothing and separating packaging materials can leave objects at different electrical potentials. Contact then provides a path for charge to move rapidly. A charged person touching a connector is one example. A charged board touching conductive equipment is another. The board itself can be the charged object.

Inside a MOSFET, the gate insulation is extremely thin. In an integrated circuit, input structures and tiny conductive regions may be vulnerable to excessive voltage or current density. An ESD event can damage these microscopic features without leaving a visible mark on the package or PCB.

Disconnecting the supply does not remove this risk. The energy for the discharge can come from a person, a tool or the board’s accumulated charge. Unpowered PLC modules, drive control boards and sensor electronics therefore need protection during storage and handling as well as repair.

Damage may cause immediate failure, increased leakage or a shift in electrical parameters. Some degradation may escape a simple initial function check. However, an intermittent fault is not proof of ESD. The absence of a visibly burnt component does not rule it out, and a burn mark does not establish it as the cause.

Built-in protection has limits

An IC’s internal protection and external TVS diodes can protect particular discharge paths. They do not make every point on the board safe to touch. Component placement and the return path for the pulse current are part of the protection design.

Component-level HBM and CDM ratings also describe different tests from IEC 61000-4-2 equipment immunity testing. A finished product’s performance with its enclosure fitted does not establish that an exposed internal board can be handled without precautions.

Can a multimeter identify ESD damage?

Resistance measurements and diode tests can reveal obvious shorts. Normal readings cannot verify every leakage specification, switching threshold or interface function. Identifying the cause may require functional and parametric measurements, or specialist failure analysis.

If a fault appeared after the board was removed and refitted, also investigate connectors, cracked or poorly formed solder joints and power-supply regulation. The sequence “handled, then failed” is a useful observation, not a complete diagnosis.

Editor’s note: I would establish a reliable handling process before using a spare board to diagnose a fault. Bringing that spare in an ordinary bag and opening it on an unchecked bench introduces another uncertainty into the repair. Verify the ESD arrangements, preserve the replacement board’s condition and base any claim of ESD damage on evidence. “It must have been static” is not a substitute for finding the fault.

Technical references: ESD Association — Introduction to ESD · ESD Association — Control procedures and materials · Analog Devices — ESD