IEC 61951
Look beyond the capacity label when choosing a nickel battery
IEC 61951 gives manufacturers and buyers a common framework for sealed rechargeable nickel cells and batteries used in portable equipment. It covers designation, marking, dimensions and electrical tests. Two products with the same mAh rating can still behave differently in service. Our battery basics and battery standards directory explain the wider context; here, the useful question is how the stated performance was measured.
Match the reference to the chemistry
For nickel-cadmium (NiCd), the consolidated reference is IEC 61951-1:2017+A1:2023. For nickel-metal hydride (NiMH), it is IEC 61951-2:2017+A1:2022. Both parts address small prismatic, cylindrical and button-format cells and batteries. Ask for the part and edition, rather than accepting an undated reference to the series.
These parts do not cover every product in a battery catalogue. Lithium-ion batteries are outside their chemistry scope. The IEC 60086 series deals with primary batteries, so a nickel rechargeable test result should not be treated as evidence for a different chemistry.
A capacity figure needs a measurement context
At a constant current, capacity equals current multiplied by discharge time. If a cell supplies 400 mA for five hours, the measured result is 2,000 mAh. That simple calculation becomes a meaningful comparison only when the discharge current, temperature, initial charging conditions and discharge cut-off voltage are also known.
A 2,000 mAh label does not promise five hours in every device. The load may vary, and the equipment may shut down at a voltage above the endpoint used in the capacity measurement. When specifying a battery pack, examine voltage under load and the intended operating temperature as well as the capacity number.
Separate the different endurance questions
Discharge performance examines operation under specified load and temperature conditions. Charge retention concerns usable capacity after a period of rest. Cycle endurance examines repeated charging and discharging, while permanent charge endurance addresses a different duty. A strong result in one category does not describe all the others.
The series also contains assessments of charge acceptance, overcharge and pressure relief features. The applicable procedure and acceptance criteria depend on the cell type and clause. There is no single cycle-life figure that can sensibly be assigned to all NiCd cells or all NiMH cells.
Stored readiness and heavy-load operation need different evidence
Equipment that spends most of its time waiting may benefit from low self-discharge. A demanding load calls for evidence of high-current performance. In Part 2, the I designation identifies low self-discharge cells; F identifies a high-recovery type associated with lower permanent capacity loss after storage. Keeping a charge while idle and recovering capacity after storage are distinct properties.
The battery charger is part of that decision. Use the manufacturer's charging current, temperature limits and termination guidance for the chosen cell type. An NTC temperature sensor can support monitoring, but adding a sensor does not make an arbitrary charging method suitable.
Physical fit is only one part of replacement compatibility
Dimensions, terminal construction and polarity help establish whether a replacement fits. They cannot establish electrical suitability on their own. Check the model designation, connection arrangement and equipment requirements when choosing battery accessories or replacement packs. A familiar form factor is a starting point, not a complete specification.
Keep performance evidence and safety evidence distinct
IEC 61951 includes some tests of protective features, but it does not automatically replace an assessment under IEC 62133. IEC 62133-1 is the nickel-system safety part. UL 2054 is another battery safety standard with its own scope. Read the reports to establish which properties were evaluated and which product construction they cover.
Editor's note
Before choosing the larger mAh number or longer cycle-life claim, ask whether the suppliers used comparable test conditions. Laboratory endurance and service life are different questions. Review the charging equipment, ambient temperature and idle periods against the actual duty of your battery system.
Related reading
NiCd batteries · NiMH batteries · IEC 62133 · IEC 60086 · UL 2054 · Battery chargers · Battery standards
Sources: IEC 61951-1:2017+A1:2023 · IEC 61951-2:2017+A1:2022 · IEC 61951-1 — Preview · IEC 61951-2 — Preview · Panasonic — NiMH handbook · Panasonic — Battery FAQ · IEC 62133-1:2026
