6ES7 193-4CB20-0AA0

6ES7 193-4CB20-0AA0 – Siemens ET 200S TM-E15S24-01 terminal module

6ES7 193-4CB20-0AA0 is the TM-E15S24-01 screw-terminal base for Siemens ET 200S electronic modules. This 15 mm-wide component with 2×4 connection points connects field wiring to the electronic module fitted onto it. Signal processing and channel count belong to that electronic module; eight terminals do not establish eight input or output channels. See the ET 200 system overview for the station architecture.

Dimensions and packaging

The Siemens data sheet specifies 15 × 132 × 43 mm, in width × height × depth order, and an approximate weight of 65 g. The manufacturer’s packing unit contains five pieces. When buying a used terminal module, check whether the offer covers one piece or a complete pack. Match the full order number on the housing to the item shown in the photographs.

AUX1 continuity and terminal functions

This version has a continuous AUX1 bus without access through the terminals. In particular, terminals 4 and 8 are not connected to AUX1; their functions depend on the installed electronic module’s wiring diagram. The power buses from the power module also continue through the base. When reviewing the station’s power supply modules and connection arrangement, check AUX1 continuity and the functions of the front terminals separately.

Examples of supported electronic modules

Siemens documentation lists this base as a usable option for the 6ES7 134-4MB02-0AB0 current input, 6ES7 134-4JB01-0AB0 thermocouple input and 6ES7 134-4JB50-0AB0 RTD input modules. For another analog input module, consult its own terminal-module selection and wiring diagrams. A matching 15 mm width alone is not enough to establish suitability.

For example, the 4MB02 manual assigns terminals 4 and 8 to L−, the return circuit for the measuring-transducer supply. That allocation belongs to the 4MB02 wiring arrangement and must not be transferred directly to another electronic module fitted on the same terminal base.

Differences from 4CB30 and 4CB10

6ES7 193-4CB30-0AA0 is the TM-E15C24-01 spring-terminal version with 2×4 connections. 6ES7 193-4CB10-0AA0 is the TM-E15C23-01 spring-terminal version with 2×3 connections. These differences matter when an application must retain screw termination or use terminals 4 and 8. Before replacement, compare conductor preparation, terminal count and the bases approved for the electronic module.

Installation and connection checks

The base fits on the ET 200S station’s 35 mm mounting rail. Inspect the rail latch, contacts joining the adjacent base and the electronic-module seating area. Siemens specifies an 11 mm stripping length and a 0.4–0.7 Nm tightening torque for screw-terminal wiring. Select conductor size and ferrules using the system manual’s wiring table, and carry out wiring with the relevant supply and load voltages switched off.

When investigating a signal problem, check terminal tightness, wire identification and the electronic module’s channel allocation together. Confirm that the input defined in the PLC project corresponds to the physical channel. Browse the 6ES7 151-1BA02-0AB0 and 6ES7 151-3BA20-0AB0 interfaces for network options, and the ET 200 PROFIBUS and PROFINET section for system background.

Editor’s Note: For a used terminal base, request close photographs of the screw openings, side contacts and rail latch as well as the front label. Record terminal numbers before disconnecting the existing wires. When changing from a base with AUX1 terminal access, compare the new diagram before transferring the previous wire layout.

Manuals and PDF documents

Relevant documents are available through the Siemens ET 200 manuals section. Section 1.9, pages 21–22 of the 04/2007 Terminal Modules manual explains the base arrangement. For installation and screw-terminal wiring, use chapters 4 and 5 of the 12/2004 ET 200S system manual. Refer to the installed electronic module’s own manual for signal allocation.

Related topics

See 6ES7 134-4NB50-0AB0 RTD High Feature for another temperature-measurement option. Browse industrial communication, PLC and HMI and Siemens S7-300 for system information.

Navigation

Siemens ET 200 | Siemens SIMATIC S7 | Siemens automation | OtomasyonAVM home