6ES7 138-4FB00-0AB0
Siemens Main Menu › SIMATIC S7 › ET 200 Modules
Siemens 6ES7 138-4FB00-0AB0 — ET 200S 4 F-DO PROFIsafe Output Module
6ES7 138-4FB00-0AB0 is a four-channel fail-safe digital output module for the Siemens ET 200S distributed I/O system. Its 24 V DC outputs, rated at 2 A per channel, control suitable actuators selected for the safety application. It belongs to the ET 200 fail-safe module range and receives safety commands through PROFIsafe safety communication.
Key technical characteristics
Complete order number: 6ES7138-4FB00-0AB0. Outputs: 4 F-DO. Rated voltage: 24 V DC. Rated output current: 2 A per channel. Width: 30 mm. Switching arrangement: P/M. Function: Fail-safe digital output with diagnostics.
P/M switching uses switching elements on the positive and negative sides of the load as part of the safety function. Do not assume the same wiring as a conventional PNP output. Matching the voltage and current ratings of standard digital output modules does not make them interchangeable in a safety circuit.
Safety capability and system compatibility
The historical Siemens product description specifies use up to Category 4 according to EN 954-1; PCS 7 module lists also identify this model for safety applications up to SIL 3. These are upper capabilities under the applicable conditions. The machine's achieved safety level depends on the sensors, controller, program, wiring and final switching elements assessed together.
Within the ET 200 station architecture, check the F-CPU, interface module and engineering software as a complete combination. When comparing PROFIBUS and PROFINET interface options, do not transfer features of later 4FB revisions to this earlier order number. Replacement with 4FB01, 4FB02, 4FB03 or 4FB04 requires verification against the exact module and existing project.
Terminal bases and power supply
The relevant Siemens accessory list includes screw-terminal bases 6ES7193-4CG20-0AA0 and 6ES7193-4CF40-0AA0, plus spring-terminal bases 6ES7193-4CG30-0AA0 and 6ES7193-4CF50-0AA0 for this F-DO. When selecting ET 200 terminal blocks, also check AUX1 access and existing wiring. Connection modules and terminal bases are separate from the electronics; confirm the delivery scope.
Compare the load group supplied by the ET 200 power modules and its power distribution connections with the cabinet schematic. Four channels rated at 2 A do not establish an unconditional 8 A module rating. Apply the simultaneous loading, ambient temperature and mounting-position limits for this hardware version.
Five checks before selection or replacement
1. Label and project: Record the complete order number and hardware version. Compare them with the STEP 7 hardware configuration; the “4 F-DO” front marking alone is insufficient.
2. Safety address: Check the module's PROFIsafe address, its project assignment and the monitoring time. Assess any address change within the existing safety project.
3. Load characteristics: Review operating and pickup current for each contactor, relay or valve coil. Verify inductive-load suppression and compatibility with test pulses; a 24 V label alone does not establish suitability.
4. Wiring and diagnostics: Check the output pairs against the correct diagram. When troubleshooting, inspect the supply, field wiring and load as well as the module, and record the diagnostic message.
5. Recommissioning: After replacement, verify safe shutdown, feedback signals and restart conditions. On a used module, an illuminated output LED does not demonstrate that the safety function is intact.
Editor's Note
Start with the complete order number, including the final revision digits. Different hardware generations can carry the same “4 F-DO, 24 V/2 A” description. Reviewing the module label, a backup of the working project and photographs of the terminal wiring together reduces the risk of choosing the wrong spare. Seeing an output turn on and off is not sufficient validation of a change to a safety circuit.
PDF manuals and technical documents: Use Siemens ET 200 user manuals and PDF documents and check the order numbers covered by each ET 200S Fail-Safe Modules manual. Do not apply 4FB03 or 4FB04 specifications directly to 4FB00. Also consult product information A5E31214701-AB for the supply-overvoltage clarification covering the relevant load-wiring application from this model onward.
Related Topics
Terminal Blocks · Connection Modules · Power Distribution Modules · Safety Modules
Otomasyon AVM
Siemens Main Menu ·
SIMATIC S7 ·
ET 200 Modules ·
ET 200 PDF Manuals ·
PLC and HMI