6ES5 241-1AA11

Siemens 6ES5 241-1AA11 – SIMATIC S5 IP 241 Two-Channel Position Decoder Basic Module

The Siemens SIMATIC S5 6ES5 241-1AA11 (IP 241) processes encoder position on two independent channels. It compares the actual position with start and end values defined in STEP 5. Each channel supports up to 16 electronic cam tracks. The PLC reads the position and comparison results from the module.

50-pin front connectors and Faston terminals

Each channel has a 50-pin Sub-D connector and a synchronization LED. On the 1AA11, Vork. 1, Vork. 2, P and M use 2.4 × 0.8 mm Faston terminals. The 6ES5 241-1AA12 uses screw terminals at these points. External 24 V DC supplies the encoders and matching modules. The Vork. inputs are used for reference-point synchronization on incremental encoder axes.

When checking S5 cables and connectors, use the pin assignment for the fitted matching module. Record the signal type and supply marked on the encoder. If the machine uses a rotary encoder, check the encoder coupling for play. When selecting a second-hand encoder, match the signal type and voltage as well as the connector.

Encoder matching modules

Each active channel takes a matching module suited to its sensor. The incremental 1AB11, Excess-3 Gray 1AC11, absolute binary/BCD 1AD12 and synchronous serial 1AF12 handle different signals. Check the full matching-module order number and the basic module's revision together. The IP 241 MIR 3CA12 is a separate model.

STEP 5 program and rack selection

FB156 loads cam limits and other settings from the data block. FB157 controls the module and reads values. FB158 provides the same functions with indirect parameters passed through a working data block. The German manual specifies module revision A14 and firmware A08 or later for parallel operation with one encoder and up to 32 cam tracks on the 1AA11.

Siemens documents the IP 241 for the S5-115U, S5-135U, S5-150S/U and S5-155U. For systems such as the S5-115U with a CPU 944 or the S5-135U with a CPU 922 or CPU 928, verify the slot and interrupt line for the installed S5 rack in section 8.8 of the manual.

Identifying the right spare

The IP 240 1AA12 and IP 240 1AA21 handle counting and position measurement. The incremental IP 246, absolute IP 246 and IP 266 are positioning modules. The IP 247 commands stepper drives. When troubleshooting, check the STEP 5 project to identify which module reads position and which commands the drive. To sell a 1AA11 module, send photos of its label and front panel to otomasyonavm@gmail.com.

Editor's note

Before removal, record the 1AA11 module revision and the full order numbers of the matching modules fitted to channels 1 and 2.

Back up the STEP 5 project and the IP 241 data block. Retain the module address, cam limits and interrupt settings for comparison.

With power isolated, label both Sub-D plugs by channel. Inspect the Faston terminals for looseness or corrosion.

After referencing an incremental channel, check that its synchronization LED goes out and verify the position value read by the PLC.

If one encoder is used with 32 cam tracks, verify that the spare meets the A14/A08 requirement and that startup loads the parallel-mode setting.

PDFs and Siemens documentation

+ Siemens IP 241 manual (DE) – 1AA11, Faston terminals and revision requirements

+ Siemens IP 241 manual (EN) – front connections, rack slots and FB156/157/158

+ Siemens S5-115U system manual (EN) – racks and installation

+ Siemens 6ES5 241-1AA11 product status sheet (EN)

+ Siemens S5 PDF archive

Related topics

+ S5 interface modules

+ S5 expansion modules and adapter casings

+ About Siemens S5 PLCs

Navigation

+ S5 positioning modules

+ SIMATIC S5 modules

+ Siemens S5 PLCs

+ Second-hand Siemens automation