6ES5 755-1AA12
6ES5 755-1AA12 Siemens SINEC H1 Repeater
The 6ES5 755-1AA12 is a network repeater for legacy SINEC H1 industrial Ethernet installations. It operates in the network infrastructure of Siemens S5 systems, regenerating signals between segments used by communications processors. Siemens Catalog ST 50 lists the complete order number as a repeater.
The triaxial SINEC H1 network discussed here uses 10 Mbit/s Ethernet based on IEEE 802.3. A repeater regenerates attenuated signals and propagates collision information between segments. The Ethernet overview and explanation of how Ethernet works provide useful background.
Transceivers, drop cables and termination
In a SINEC H1 installation, a repeater connects to the bus through transceivers and 727-1 drop cables. A 6ES5 755-0AA13 transceiver performs a different job from the repeater. When selecting S5 cables and connectors, check the interfaces at both ends against the installed wiring.
Each triaxial bus segment requires 50 Ω termination at both ends. Inspect the 6ES5 755-3AA11 terminators separately from the 6ES5 755-4AA11 N-type coaxial connection parts. Installing a repeater cannot compensate for missing or incorrect bus termination.
Segment length and network expansion
Siemens specifies a maximum segment length of 500 m and no more than two repeater units in the path between two stations. Remote repeater configurations require their own unit-counting rules. Consider cable type and Ethernet speed together; these limits do not describe modern copper Ethernet cabling.
Distinguish the Ethernet protocol from the physical connection when selecting replacement equipment. Document the legacy network before treating the task as a switch or hub selection. An Ethernet product name alone does not establish direct compatibility with the existing SINEC H1 connection.
Commissioning and communication checks
Transceivers connected to a repeater must have the SQE/heartbeat test disabled. Where CP 535-3LB11 or CP 535-3MA12 communications processors are installed, record the segment used by each station before changing hardware. Preserve the existing communication parameters during replacement.
Check the state of the SIMATIC S5 station separately from its external network connection. Losing access to one station does not establish a repeater fault. Inspect S5 interface modules, the communications processor, transceiver and cable route according to their roles in the installation drawings.
Selecting the complete order number
Match supply, dimensions and connection details for the 6ES5 755-1AA12 against the actual equipment label. The 6GK1 110-0AA00 described in the final chapter of the Siemens network manual is a different model; its technical table must not be transferred to this device. The S5 expansion modules and Siemens S5 PLC overview help distinguish the product groups.
When purchasing used Siemens automation equipment, request photographs of the label, ports and test arrangement. Record how the existing network operates and the results after replacement. The Ethernet FAQ provides background information; it does not replace testing the actual unit.
Editor’s Note
A power indicator alone is not a complete communication test. Confirm that real traffic passes between the two segments before accepting the repeater as operational.
Photograph and label both sides before disconnecting cables. Losing track of segment connections in an older installation can lead to a healthy component being misdiagnosed.
Inspect the bus termination early. A missing or incorrect end component can waste time on unnecessary hardware replacement. Have the wiring checked against the installation drawings.
Test used equipment with known-good transceivers and cables wherever possible. A faulty drop cable can otherwise make the repeater appear defective.
Record the complete order number and supply information from the label. Do not apply dimensions or electrical ratings found for another Siemens repeater, and ask for more than a front-panel photograph when buying a replacement.
OtomasyonAVM resources and PDFs
+ S5 communications modules · S5 expansion modules and network accessories
+ Shared Siemens S5 PDF archive. This is a general system-manual archive, rather than a dedicated manual for this repeater.
Related topics
+ SINEC H1 transceiver · Bus terminators · Coaxial connection parts
Browse SIMATIC S5
+ S5 expansion modules · S5 communications modules · Siemens S5 PLC · Siemens second-hand equipment
Siemens and external references
+ Siemens Catalog ST 50, 1998 — English, section 4/126, PDF page 288. Lists the exact 6ES5 755-1AA12 order number as a repeater.
+ Siemens SIMATIC NET — Manual for Triaxial Networks, B8976055/04, English. Chapter 2 explains SINEC H1 network structure and repeater connection rules. The equipment ratings for the 6GK model in Chapter 6 must not be treated as specifications for the 755-1AA12.