6ES5 451-8MA11
Siemens 6ES5 451-8MA11 – 8-Channel 24 V DC Digital Output Module
6ES5 451-8MA11 is an 8-channel electronic digital output module rated at 24 V DC / 1 A in the Siemens SIMATIC S5 family. This S5 output module provides optocoupler isolation for one group of eight channels. In addition to the 1 A per-channel limit, total output current must not exceed 6 A.
The manufacturer's description lists SIMATIC S5 S5-90U, S5-95U, S5-100U, ET 100U and ET 200U applications. Check the appropriate bus module, arrangement and addressing against the existing S5 system architecture.
Load voltage and current limits
Nominal load supply is 24 V DC, with a permissible range of 20–30 V DC including ripple. Assess module electronics and external loads when calculating power supply and PLC supply requirements.
The specified output load-current range is 5 mA–1 A, with a maximum 10 W lamp load. When selecting a contactor or control relay coil, check inrush current as well as continuous current.
All eight outputs cannot deliver 1 A simultaneously. Include the 6 A total limit in fuse selection, wiring selection and load-current calculations. Eight loads drawing 0.8 A each total 6.4 A and exceed this limit.
Short-circuit protection and automatic recovery
The outputs have electronic short-circuit protection and automatically resume operation when the short circuit is removed. The red F LED indicates a short circuit. Check the affected load and field wiring when protection operates.
Terminal connections
The manufacturer's drawing identifies L+ as terminal 1 and M as terminal 2. Compare S5 connection parts and the connector/terminal arrangement with this diagram.
Channel → terminal: .0 → 4; .1 → 3; .2 → 6; .3 → 5; .4 → 8; .5 → 7; .6 → 10; .7 → 9. Numerical terminal order does not follow channel order .0–.7.
Switching and operating characteristics
Maximum switching frequency is 100 Hz for resistive loads and 2 Hz for inductive loads. Off-state residual current can reach 0.5 mA; consider this when assessing low-power loads in the off state.
Typical power dissipation is 3 W, with an approximate weight of 230 g. Review electromagnetic interference sources and earthing connections in the cabinet.
Addressing and testing
Match the output addresses in the CPU project to the PLC program. During troubleshooting, check the program command, F LED, L+/M supply and actual load current together.
Related order numbers and used-module checks
6ES5 441-8MA11 has 0.5 A DC outputs, 6ES5 451-8MD11 has AC outputs, and 6ES5 451-8MR12 has relay outputs. 6ES5 453-8MA11 has different voltage/current specifications. Use the complete order number when selecting a replacement.
On used Siemens equipment, inspect the label, bus contacts, terminals and signs of overheating. Test all eight outputs with suitable loads while observing both channel and total current limits.
Editor’s note
Keep both figures in mind: 1 A per channel and 6 A in total. Each load may look suitable on its own while the combined current is too high. Add up the loads that operate together before it becomes a heating problem.
Record the wire numbers before disconnecting anything. Channel .0 goes to terminal 4, and channel .1 goes to terminal 3. Follow the drawing for the remaining channels; wiring them in numerical order out of habit will cause confusion here.
If the red F LED is lit, check before condemning the board. Start with the coil, field cable and damaged wiring. Fitting another board before finding a load-side short circuit brings the same fault straight back.
Remember that the output can recover automatically when the short circuit is removed. If the PLC command remains active, the load may operate again. Isolate the supply before working on the fault instead of relying on the protection to keep the output off.
With a used module, an illuminated LED is a useful start; verify that the load actually operates. Test every channel and give the connections one final check. Those few minutes help you leave the machine with confidence.
OtomasyonAVM resources and PDFs
Start with the OtomasyonAVM Siemens S5 PDF archive, About Siemens S5 and S5 digital output modules. The exact technical table and terminal drawing appear on printed page 2-29 / PDF page 43 of the ET 100U manual below.
Related topics
+ 6ES5 441-8MA11 · 6ES5 451-8MD11 · 6ES5 451-8MR12 · 6ES5 453-8MA11.
+ Fuse rating and load current · PLC troubleshooting · Relays and sockets.
Browse SIMATIC S5
S5 digital output modules · S5 connection parts · S5 PDF archive · Used Siemens equipment
Siemens and external references
+ Siemens ET 100U Distributed I/Os Manual – English: printed 2-29 / PDF 43, specifications and connections for 6ES5 451-8MA11.
+ Siemens S5-100U Programmable Controller Manual – English: printed 14-31 / PDF 381, the detailed technical table for the same model.