6ES5 432-6AA12

Siemens 6ES5 432-6AA12 — 16-Channel 24 V DC Digital Input Module with Group Signal

The Siemens 6ES5 432-6AA12 is a galvanically isolated digital input module with 16 inputs at 24 V DC and a group-signal function for S5-130A and S5-150A systems in the SIMATIC S5 family. Within the S5 digital input range, it uses the rugged Robustbauform A construction.

It transfers contact and suitable electronic sensor signals to a Siemens S5 PLC. Its group signal, or Sammelsignal, distinguishes it from ordinary input modules. When selecting a spare, check the S5 rack, complete order number and the project’s use of the group-signal function together.

24 V DC inputs and signal thresholds

Nominal input voltage is 24 V DC. The specified logic-0 range is −33 to +4.5 V, with logic 1 at +13 to +33 V and typical logic-1 input current of 5 mA. These threshold ranges do not change the module’s nominal 24 V rating.

A relay contact can switch the appropriate 24 V source. For electronic sensors, check the PNP/NPN output arrangement, reference conductor and actual input voltage. With two-wire sensors, assess off-state current too; a 24 V label alone does not establish compatibility.

2 ms delay and the 50 µs option

The manufacturer specifies a typical input delay of 2 ms, reducible to 50 µs. Check the existing board’s settings before assuming that all inputs operate at 50 µs. This is an input-delay figure, not the execution time of the entire CPU program.

Maximum cable lengths at 2 ms delay are 400 m unshielded and 1000 m shielded. Shorter delays require shorter cables. Do not combine the 50 µs setting with those long-distance limits as though they were guaranteed together. For short pulses, consider cabling, interference and CPU processing as one application.

Isolation, power and the two-byte connection layout

The field inputs are galvanically isolated. The connection drawing identifies the first eight channels as Byte 0 and the remaining eight as Byte 1; wire their L+ and L− connections according to that drawing. Check the front connections and cables, and do not substitute protective grounding for a signal-return conductor.

Current consumption from the internal 5 V supply is 270 mA. Separate this from field input currents in S5 power-supply calculations. The internal 5 V powers the module’s logic; nominal input signal voltage remains 24 V DC.

Group signal and address checks

The Sammelsignal function supports the use of input events in the system’s alarm processing. Verify the interrupt or alarm sequence against the installed CPU and PLC program. The ST 53 catalog specifies a maximum of eight 432-6 group-signal modules; account for this when expanding the installation.

Byte 0/Byte 1 in the wiring drawing describes the module’s channel arrangement, not its absolute PLC start address. During troubleshooting, trace the physical channel, channel LED, program input address and group-signal handling against the same record.

Differences from similar order numbers

The 430-6AA11 has 32 inputs at 24 V DC, while the 431-6AA11 has 16 inputs with 24/60 V DC selection. The 432-6AA12 combines 16 inputs at 24 V DC with a group signal. Similar channel counts or housings do not replace that function.

The 432-3BA12 uses compact K construction. The 432-4UA11 and 432-4UA12 belong to the U construction family; the 4UA12 has 32 inputs. The 432-7LA11 is a 48–60 V AC/DC input module for the S5-115U. These versions should not be assumed to be plug-in replacements for the A-type 6AA12.

Editor’s note

Give this board a fuller description than just “16 inputs, 24 volts.” If the machine uses its group signal, the spare has to perform that job too. Start with photographs of the original order number and settings; a clear record makes the next steps much easier.

The 50 µs option can be useful, but there is no need to select the shortest delay automatically. If the machine runs correctly at 2 ms, first establish why a change is needed. Contact bounce and cable interference can become more visible with a faster input.

If one byte works and the other does not, return to the wiring drawing before condemning the board. Check each section’s L+ and L− connections, connector contact and actual signal voltage separately. A small supply connection can cause a long fault-finding session.

An illuminated channel LED does not confirm the complete alarm path. Watch the input bit and the part of the program that handles the group signal together. A signal reaching the module and the machine responding correctly are two separate checks.

For a used Siemens purchase, request clear views of the label, board surface and setting areas. When assessing a used digital input module, ask for all 16 channels and the application’s group-signal function to be checked. Give the spare a complete check before relying on it to keep the machine running.

OtomasyonAVM resources and PDFs

+ OtomasyonAVM S5-115 PDF archive. For the 432-6AA12’s S5-130A/S5-150A specifications, use the ST 53 catalog below. S5-115U connection drawings should not be applied directly to this A-type module.

Related topics

+ 430-6AA11 · 431-6AA11 · 432-3BA12 · 432-4UA12 · 432-7LA11 · PLC troubleshooting.

Browse SIMATIC S5

+ S5 digital input modules · S5 cables and connectors · SIMATIC S5 · Siemens S5 PLCs · Used digital input modules · Siemens second-hand main page.

Siemens and external references

+ Siemens ST 53, 1985 — S5-130/S5-150; printed page 2/12: A-type systems and eight-module limit; 8/5: specifications; 8/20: connection drawing; 9/6: exact 432-6AA12 order number; externally archived Siemens publication.

+ Siemens S5-135U/155U system manual — section 8.4.4: the different U-type 432-4UA12 used in the comparison.

+ Siemens S5-115U manual — 48/60 V UC specifications of the 432-7LA11 used in the comparison.