6ES5 318-8MB11
Siemens 6ES5 318-8MB11 — IM 318-B ET 200U Slave Interface Module
The Siemens 6ES5 318-8MB11 is the IM 318-B slave interface module for an ET 200U station built with SIMATIC S5 I/O. It connects the station to SINEC L2-DP using the DP Siemens protocol and requires 24 V DC. Within the S5 interface module range, it serves as the distributed I/O station’s interface head.
It handles data exchange between the central Siemens S5 PLC and the field I/O group. When assessing S5 communications modules, retain the exact MB11 suffix and DP Siemens requirement as part of the selection.
DP Siemens protocol and master compatibility
Siemens specifies COM ET 200 V1.0 or later and an IM 308-B from hardware revision 1. Check the full number and revision of a master such as the 6ES5 308-3UB11 IM 308-B against the existing project. Both sides of the master–slave link must support the same protocol.
The MB11 does not implement DP Standard/DP-Norm. Matching PROFIBUS connectors and cables does not establish compatibility with a standard DP master. Before migrating to another master, assess its DP Siemens support and the station configuration.
Differences from MB12 and other 318 variants
The 318-8MB12 adds DP Standard support to the MB11 functionality. Treat the two numbers as distinct versions. For other variants, including the 318-8MB13 and 318-8MC12, check protocol and configuration requirements against the exact part number.
Assess the 318-8MA12 separately rather than selecting it from the shared IM 318 designation. A replacement assessment must match the connection role, master type, project file and installed I/O order.
Station address and switch 8
Set the station address in binary using switches 1–7. On the MB11, switch 8 at ON places the internal I/O bus in Slow Mode. It does not enable DP Standard on this version and is separate from the address setting.
Record all switch positions before replacement. Check that the station number matches the master project and is not duplicated elsewhere on the network. Establish each switch’s function before copying settings from another 318 variant.
I/O expansion and supply
An ET 200U station accommodates up to 32 suitable S5-100U I/O modules, with an address space of 32 input bytes and 32 output bytes. When selecting digital inputs, digital outputs and analog modules, assess the supported module list, address requirements and total I/O-bus current together.
Multiple-tier arrangements use expansion interfaces such as the IM 315 — 315-8MA11 and IM 316 — 316-8MA12. Match the layout to the relevant instructions. The permitted range for the module’s 24 V supply is 20–30 V DC. Check field-load supplies separately from the station electronics supply.
Bus connection and fault checks
When selecting Siemens PROFIBUS connectors and S5 cables and connectors, check the line ends, termination, shielding and mechanical connections. During PLC troubleshooting, start with station power, then the address, cabling and master configuration. Next compare the installed I/O order and module addresses.
Editor’s note
Take a moment to check the last two digits. With an MB11 in hand, follow its own instructions before applying settings described for an MB12. Establishing protocol compatibility early is especially useful when changing the master.
Give switch 8 a defined purpose in the diagnosis rather than changing it at random. On the MB11 it slows the internal I/O bus. Photograph the address switches before removal so the replacement starts from a clearly recorded arrangement.
If several inputs and outputs disappear together, start with the station supply and shared communications path. Checking the common points first can save you from replacing several serviceable I/O modules.
Record the I/O order before changing the interface head. Missing an analog module or a unit occupying two slots can leave the machine addressing the wrong data even after communication returns. A small amount of careful recording prevents a great deal of confusion.
When buying a used Siemens module, seek more than illuminated LEDs. Check recognition by a suitable DP Siemens master and stable I/O data exchange. Include the label, switch bank and connectors in the condition assessment.
OtomasyonAVM resources and PDFs
+ Siemens ET200 manuals · S5 PDF archive.
+ S5 interface modules · S5 digital inputs · S5 digital outputs · S5 analog modules. Consult the ET 200U manufacturer’s manual below for MB11-specific protocol and switch information.
Related topics
+ IM 308-B master · 318-8MB12 · 318-8MB13 · PROFIBUS connectors · PLC troubleshooting.
Browse SIMATIC S5
+ S5 interface modules · SIMATIC S5 · Siemens S5 PLCs · Siemens second-hand main page.