6ES5 921-3WB13
Siemens 6ES5 921-3WB13 CPU 921 — S5-130WB / SINUMERIK PLC
Siemens 6ES5 921-3WB13 is the CPU 921 processor for the S5-130WB central controller and integrated PLC 130WB used with SINUMERIK 3/8. This CPU belongs to the SIMATIC S5 family and executes the machine’s PLC-side STEP 5 program. Assess a replacement against the CPU label, installed PLC arrangement and fitted program memories.
921-3WB11, 921-3WB14 and 921-3WB15 are different order codes within the WB group. 921-3WA13 and 921-3UA12 are separate models as well. The “CPU 921” name alone does not establish unchanged program, memory and hardware compatibility; compare the complete code and revision.
130WB memory arrangement and EPROM modules
Siemens’ System 8 manual describes two EPROM submodule positions and user RAM for 2.9 K instructions in its 921-3WB family section. That section also lists user-program options up to 16 K instructions. These are family figures expressed in instructions; they should not be combined into a claimed total internal RAM capacity for WB13.
For the SINUMERIK application, the first module is assigned to the basic program and the second to the user program. Record memory submodule codes, program labels and fitted positions. Identify whether these modules accompany a replacement CPU; installed hardware alone does not establish the presence of the machine’s program.
PG connection and program backup
The S5-130W Version B family manual describes an AS 511 connection for programming with PG 670/675. Check the programming interface, PG cable and existing communication arrangement together. Compare cable, interface and software settings before treating a connection problem as a CPU fault.
Back up the accessible PLC program and data blocks before removing the CPU or memory. Keep SINUMERIK NC data and PLC program backups separately identified. Siemens’ System 8 documentation also describes reading USTACK to investigate a STOP; capture fault information before resetting the controller.
Supply, rack and board inspection
Check the power supply and rack connections against the installed controller’s documentation. Inspect board connectors for bent contacts, poor contact, oxidation and previous repairs. Preserve the program before shutting down equipment with a battery or retention warning; install and remove boards with power isolated.
The numerical technical table in the S5-130W Version B manual explicitly identifies 921-3WB11. Its current, processing-time and weight figures should therefore not be presented as confirmed WB13 specifications. Distinguish values verified for the exact WB13 revision from general family descriptions.
Functional checks on the machine
Compare digital inputs, digital outputs and analog modules with their PLC addresses. Record the states of function modules, position-control equipment and special modules separately. After CPU replacement, verify interlocks and machine sequences under controlled conditions.
For an older Siemens S5 system, check program access, I/O exchange and machine data interaction as well as the RUN indication. Identify the controller, memories and functions actually tested in the report. Visual inspection alone is not a complete operating test.
Editor’s note
Confirm the 3WB13 suffix first. A different version advertised simply as a “921 CPU” should not be assumed to operate unchanged on the same machine.
Photograph the memory positions. Keep the basic-program and user-program modules identified and record where each was fitted. A bare CPU and a complete set carrying the machine’s program are different deliveries.
An operating NC display does not establish a complete PLC backup. Preserve the PLC program and data blocks separately, especially when only one working hardware set remains.
Read USTACK and existing fault information before clearing or resetting a stopped controller. An unrecorded reset can remove useful evidence alongside program data.
Ask which system and memories were used for testing. The report should identify the label, revision, program access and operation after warming up, so the stated condition has a clear basis.
OtomasyonAVM resources and PDFs
+ 6ES5 921-3WB13 product and information page, S5 CPU pages and Siemens S5 models.
+ OtomasyonAVM SIMATIC S5 PDF archive. Compare the exact order code with the scope of 130WB and SINUMERIK documents.
Related topics
+ 921-3WB11, 921-3WB14, 921-3WB15, 921-3WA13 and 921-3UA12. These links support model comparison and do not establish direct replacement compatibility.
Browse SIMATIC S5
S5 CPU | SIMATIC S5 | Memory submodules | Siemens second-hand homepage
Siemens and external references
+ Siemens System 8, Inbetriebnahmeanleitung, PC section I/2, German — section 18, printed pages 18-2–18-5 / PDF pages 163–166, A 03.84: 921-3WB family memory, basic/user-program modules and USTACK. This is not an exact WB13 data sheet.
+ Siemens S5-130W Version B Betriebsanleitung, GWE 548/002 J, German — section 1.4.2: the technical table covers 921-3WB11; other sections provide family architecture, AS 511 and diagnostic context.