6ES5 454-7LA12

Siemens 6ES5 454-7LA12 — 16-Channel 24 V DC / 2 A Digital Output Module

The Siemens 6ES5 454-7LA12 is an optocoupler-isolated digital output module with sixteen 24 V DC / 2 A outputs in the SIMATIC S5 family. Its outputs form four groups of four channels. Within the S5 digital output range, it switches 24 V DC loads; selection must account for both individual-channel and group-current limits.

It is listed for S5-115U/H/F systems. Match the complete order number, front connector and group supply connections to the existing installation in a suitable Siemens S5 PLC and S5 rack arrangement.

2 A per channel and the group-current limit

The nominal output current is 2 A per channel. However, the manufacturer limits each group’s total current to 50% of the sum of its channel ratings. For four channels, this gives 4 × 2 A × 50% = 4 A per group. All four outputs in a group therefore cannot carry 2 A simultaneously.

Calculate the combined demand of simultaneously operating valves, lamps and other loads when assigning groups. Assess the S5 power supply separately from the external load supply; a running rack does not establish that every output group has a healthy load supply.

24 V load supply and front connector

The external load supply is nominally 24 V DC, with a permissible range of 20–30 V DC. The logic-1 output voltage is specified as at least L+ − 3 V. When selecting S5 cables and connectors, check the catalog-listed 490-7LB11 screw-terminal front connector and the existing terminal arrangement.

Trace each group’s L+ and M connections against the module drawing. Inspect terminal fastening, conductor size and protective grounding. Isolate power before removing the module or front connector.

Electronic protection and inductive loads

The module has electronic short-circuit protection. Connecting outputs in parallel to increase current is not permitted. Maximum logic-0 leakage current is 1 mA, and the maximum lamp load is 10 W per channel.

The maximum switching frequency is 0.27 Hz for inductive loads, including relay and valve coils, and 100 Hz for resistive loads. Where the existing coil protection uses a diode, inspect its connection and polarity too. Assess switching duty together with the load-protection arrangement.

Checks under load and cabinet heating

During PLC troubleshooting, check the program’s output command, then the relevant group supply and voltage at the load. If several outputs in one group fail together, include the common supply and connector contacts in the investigation.

The specified internal 5 V consumption is 50 mA; no-load consumption from L+ is 8.5 mA per group. Typical module power dissipation is 20 W, with an approximate weight of 1.1 kg. Include cabinet ventilation and airflow around the board in the assessment.

Similar codes and different output types

The 454-7LB11 has eight outputs in a different arrangement. Do not assume interchangeability with the 454-7LA11 from the similar order number alone. The 451-7LA11 is a 32-channel 24 V DC / 0.5 A module. Match channel count and load limits together.

The 455-7LA11 and 456-7LA11 belong to the AC output range, while the 458-7LC11 has relay outputs. DC electronic outputs, AC outputs and relay contacts require different loads and connection arrangements.

Editor’s note

Start by separating the 2 A channel rating from the group’s total allowance. Write down each load and mark which ones operate together. A short calculation can prevent a fault that otherwise appears only as demand increases.

A machine may have worked for years, but two newly added valves can change the load on one group. The original arrangement and today’s installation need separate consideration. Include later additions in the calculation.

When a whole group stops working, do not immediately assume that four channels have failed together. Check the shared supply, return path and front connector first. A loose or overheated connection can make a sound board look faulty.

An unloaded test tells you something; a suitable loaded test tells you more. Watch for interruption after warm-up and voltage drop when a group operates together. Look for the fault once the real operating conditions have developed, as well as at startup.

When buying a used Siemens 454-7LA12, request clear photographs of the connector area and board surface as well as the label. Where possible, test every group with suitable loads. A few working channels do not establish the condition of the remaining outputs and group supplies.

OtomasyonAVM resources and PDFs

+ OtomasyonAVM S5 PDF archive. See page 15-35 of the S5-115U manufacturer manual below for this module’s connection drawing and load limits.

Related topics

+ 454-7LB11 · 454-7LA11 · 451-7LA11 · 490-7LB11 front connector · S5 power supplies · PLC troubleshooting.

Browse SIMATIC S5

+ S5 digital output modules · S5 cables and connectors · SIMATIC S5 · Siemens S5 PLCs · Siemens second-hand main page.

Siemens and external references

+ Siemens S5-115U manual — English; EWA 4NEB 811 6130-02b; page 15-35: 454-7LA12 specifications, group-current limit and connection drawing.

+ Siemens ST 50, 1998 catalog — English; pages 3/39–3/40: digital output specifications and ordering data; externally archived copy of the Siemens publication.

+ Siemens S5 to S7-1500 migration guide — English; 105106251, 04/2015; Appendix 7, page 41: S5-115U digital output types.