6ES5 441-7LA11

Siemens 6ES5 441-7LA11 — 32-Channel Digital Output Module

Siemens 6ES5 441-7LA11 is a 32-channel digital output module rated at 24 V DC and 0.5 A per channel for SIMATIC S5-115U/H systems. This version in the S5 digital output range is non-floating, without galvanic isolation. The reference connection between the control and load circuits is therefore an essential part of installation.

Nominal load voltage is 24 V DC, with a permitted range of 20–30 V DC. Typical loads include suitable interposing relays, valve coils and indicators. When sizing the power supply, consider operating current together with load inrush.

Common reference and front connector

The outputs are arranged in groups of eight; this grouping does not provide galvanic isolation. Siemens requires the external load reference Mext to be connected to the internal reference Mint by an external conductor. The manual limits voltage drop across that connection to 1 V. Check grounding and equipotential bonding alongside measures against electromagnetic interference.

Match the front connector and wiring to the module’s terminal diagram. The manual lists 6ES5 490-7LA11 as a 46-terminal crimp connector option. Record the connector type, contacts and existing jumpers before transferring wiring to another module.

Current, temperature and switching limits

Nominal channel current is 0.5 A, with a maximum 5 W lamp load. Permitted total output current is 100% of the nominal sum at 25 °C and 50% at 55 °C. Assess the rack arrangement and cabinet temperature against the loads energized simultaneously. Do not connect outputs in parallel to increase current capacity.

Short-circuit protection is electronic. Output voltage at signal “1” is at least L+ − 2.5 V; leakage at signal “0” is at most 1 mA. Maximum switching frequency is 100 Hz for resistive loads and 0.5 Hz for inductive loads. Apply the limit appropriate to the connected load.

Addressing and related part numbers

32 outputs correspond to four output bytes. Establish the starting address from the slot and the addressing arrangement of the installed interface module. Compare the PLC program with field-wire numbering. During troubleshooting, check the program command, load supply and output voltage under load separately.

6ES5 441-7LA12 and 6ES5 441-7LA13 are different revision codes; check the complete number and wiring arrangement before replacement. 6ES5 451-7LA11 has the same 32 × 24 V DC / 0.5 A rating but provides optocoupler-based galvanic isolation. Assess other output models, including 6ES5 454-7LA11 and 6ES5 457-7LA11, against their own load and signal specifications.

Editor’s note

Before replacing a module in this Siemens S5 system, take a clear photo of its label and front connector. The difference between 441 and 451 includes their isolation arrangement. Matching the channel count alone is not enough.

If output voltage falls when a load is connected, check the supply before condemning the module. Measure L+ and the Mext–Mint reference connection under load. A loose common connection can make a healthy module appear faulty.

One or two working outputs do not establish the condition of all 32 channels. Test each channel with a suitable load, paying extra attention to outputs that have continuously driven valves or relays. A loaded measurement tells you more than an unloaded voltage reading.

If faults appear as the cabinet warms up, recalculate the total output current. Back up the program and memory arrangement, and record wire markings. Isolate the supply and verify that the equipment is de-energized before removal or wiring work.

When buying used Siemens modules, inspect front contacts for darkening, looseness and previous repair work. Ask for a record showing all 32 channels tested under load. A sound connector and a clear test record can save considerable work later.

OtomasyonAVM resources and PDFs

+ S5 digital output modules

+ OtomasyonAVM S5 PDF archive

+ Siemens S5-115H system manual — English; 441-7LA11 specifications, p. 17-23

Related topics

+ 6ES5 441-7LA12 — different revision

+ 6ES5 441-7LA13 — different revision

+ 6ES5 451-7LA11 — galvanically isolated output

+ 6ES5 490-7LA11 — crimp front connector

Browse SIMATIC S5

+ S5 digital outputs · S5 power supplies

+ SIMATIC S5 overview · Used Siemens equipment

Siemens and external references

+ Siemens S5-115H, Edition 03, EWA 4NEB 811 6111-02b — English; p. 17-23: exact 6ES5 441-7LA11 specifications

+ Same manual, p. 3-45 — Mext–Mint connection for non-floating modules