6ES5 431-8MC11

Siemens 6ES5 431-8MC11 — 8-Input 115 V AC/DC Digital Input Module

Siemens 6ES5 431-8MC11 is an 8-input, 115 V AC/DC digital input module used in SIMATIC S5-100U and documented ET 100U / ET 200U configurations. This version in the S5 digital input range uses optocouplers, with one galvanically isolated group of eight inputs. The channels are not individually isolated from one another.

The specified voltage ranges are 0–40 V for logic “0” and 85–135 V for logic “1”. AC signal frequency is 47–63 Hz. Typical applications include monitoring suitably rated control contacts and relay contacts. Check the signal voltage rather than treating this as a 24 V input module.

AC/DC input current and response time

Typical current at logic “1” is 12 mA at 115 V AC and 2.5 mA at 115 V DC. Typical delay is 10 ms for a 0 → 1 transition and 20 ms for a 1 → 0 transition. With two-wire sensors, check residual current and circuit voltage; do not select a two-wire sensor from its wire count alone.

Terminal sequence and common reference

The front connection identifies terminal 1 as L1 and terminal 2 as N. Channel mapping is .0 → 4, .1 → 3, .2 → 6, .3 → 5, .4 → 8, .5 → 7, .6 → 10, .7 → 9. Terminal numbering does not follow channel order. Compare the wiring with the module’s front diagram.

Record the installed bus-unit number, mechanical coding and contact condition, including units such as 6ES5 700-8MA11. Check the common N connection and field wiring as part of the mounting arrangement. Isolation as one eight-input group does not establish suitability for independently referenced channels.

Internal supply, temperature and cable length

Typical module consumption from the CPU-side +9 V rail is 32 mA, with typical power dissipation of 2.5 W. Distinguish this internal consumption from the 115 V field signal when assessing the system power supply. Permitted ambient temperature is 0–60 °C for horizontal mounting and 0–40 °C for vertical mounting.

The manual gives a maximum unshielded cable length of 100 m. Assess grounding, cable routing and electromagnetic interference in the actual installation. A voltage measured on an open or disconnected line should not automatically be treated as a valid input signal.

Addressing and related modules

Eight inputs correspond to one input byte. Establish the starting address from the interface module, slot and system configuration, then match bits .0–.7 in the PLC program to field markings. During troubleshooting, compare terminal voltage, the channel indicator and the program’s input state.

6ES5 431-8MA11 belongs to the 24 V DC input class, while 6ES5 431-8MD11 is rated for 230 V AC/DC. 6ES5 430-8MC11 is a different four-input module in the 115 V class. Check the complete part number, voltage and channel count when selecting a spare.

Editor’s note

Start by reading the 8MC11 suffix carefully in this Siemens S5 system. MC, MA and MD look similar but have different input-voltage ratings. Keep a clear photograph of the original label.

Do not condemn the module because its LED stays off during a 24 V test. Its logic “1” range is 85–135 V. Use a suitably protected test arrangement, establish whether the signal is AC or DC, and select the meter range accordingly.

If several inputs disappear together, check the common N connection, terminal tightness and bus contacts before assuming multiple channel failures. A loose common connection can make a small fault look much larger.

Back up the program and memory arrangement, and photograph the channel-to-terminal mapping before removal. Isolate the supply and verify that the equipment is de-energized. Do not transfer wires on the assumption that adjacent terminals 3–4 or 5–6 follow channel order.

When buying a used Siemens module, ask for a record covering all eight inputs tested at the correct voltage. Inspect terminals for darkening, cracks and looseness. One working channel does not establish that the other seven have been tested.

OtomasyonAVM resources and PDFs

+ S5 digital input modules

+ OtomasyonAVM S5 PDF archive

+ S5 bus connections, cables and connectors

Related topics

+ 6ES5 431-8MA11 — 24 V DC input

+ 6ES5 431-8MD11 — 230 V AC/DC input

+ 6ES5 430-8MC11 — four-input 115 V module

+ 6ES5 700-8MA11 — bus unit

Browse SIMATIC S5

+ S5 digital inputs · S5 power supplies

+ SIMATIC S5 overview · Used Siemens equipment

Siemens and external references

+ Siemens S5-100U system manual — English, EWA 4NEB 812 6120-02b; p. 14-23: 431-8MC11 specifications and terminal diagram

+ Siemens ET 100U manual — English, EWA 4NEB 812 6040-02a; p. 2-21: exact-code module specifications