6ES5 430-4UA11

Siemens 6ES5 430-4UA11 – 32-Channel 24 V DC Digital Input Module

Siemens 6ES5 430-4UA11 is a 32-channel, 24 V DC digital input module for SIMATIC S5 S5-135U / U-range peripherals. All 32 inputs share one isolation group.

It passes on/off signals from pushbuttons, limit switches and field sensors to the PLC. When connecting an inductive sensor or photoelectric sensor, check the positive 24 V signal, return reference and sensor output type together. Identify PNP/NPN operation from the device information, rather than wire colours alone.

Signal levels and isolation

Logic 0: −3 to 7 V; logic 1: 13 to 33 V; rated input current: 7 mA. Treat the region between the two thresholds as undefined. Measure each signal against the appropriate field reference.

Isolation does not make every channel an independent potential group. When comparing the 6ES5 420-4UA11, 6ES5 432-4UA11 or 6ES5 431-4UA12, examine the reference wiring and isolation arrangement before considering the channel count.

Power, front connector and enable circuit

L+/L− supply: 24 V DC (20–30 V); F+/F− enable input: 24 V DC. Check the power supply at the module connection as well as at the supply terminals.

Inspect the front connector for loose terminals, corrosion and incorrect links. Label the wires before removing S5 cables and connectors; consult the wiring diagram before adding any F+/F− bridge. Checking sensor power separately from the enable circuit helps narrow down a loss affecting several inputs.

Signal speed and PLC addressing

Maximum input frequency is 100 Hz; typical delay is 3 ms. CPU scan time and program execution add to the machine’s response. Do not rely on that delay alone when capturing short pulses; assess suitable S5 function modules for the application.

32 bits represent four bytes of input data. For example, a project configured with start address 64 would be checked against I64.0…I67.7. This illustrates the mapping; it is not a fixed module address. When reviewing the Siemens S5 PLC architecture, record both the address switches and the program’s input references.

If the module is installed in an expansion rack, include the S5 interface modules and rack connection in the checks. If the data is transferred to another station, trace the path through the communications modules separately. A front-panel indication alone does not prove that the expected program address contains the correct signal.

Revision checks and module selection

4UA11 is an essential part of the order number. Do not approve the 6ES5 430-4UA12, 6ES5 430-4UA13 or 6ES5 430-4UA14 as an unconditional replacement based on appearance. Review Siemens’ revision records, the existing connector wiring and the machine’s hardware list together.

This module reads field signals. Loads are controlled through S5 digital output modules; the 6ES5 441-4UA11 and 6ES5 451-4UA11 belong to that separate product group. Record the complete input or output module number when reporting a fault.

Editor’s Note

Start with the full label. “430” on the front is only part of the story: photograph the 4UA11 suffix and the hardware revision. A spare is much more useful when its identity is clear before the machine needs it.

One working channel is a good start, but keep going. Switch every input on and off, checking both the indication and its PLC address. Include the unused channels; they may be the ones you need at the next modification.

If all the inputs disappear together, give the module a fair chance. Check L+/L−, the return connection and the F+/F− enable circuit first. One loose connection can make a healthy board look faulty.

Remember that these inputs share an isolation group. Avoid casually joining separate supplies, and take clear wiring photographs and wire-number records before unplugging the connector. In an older cabinet, those few minutes often save a long search later.

A clean cover is welcome, but buy a used module on the strength of its checks. Inspect the front connector, terminals, rear contacts and signs of overheating, then test it at the addresses used by the machine. Write down which channels were tested so the next person has evidence to work from.

OtomasyonAVM resources and PDFs

+ Siemens S5 digital input modules and the SIMATIC S5 main directory.

+ OtomasyonAVM shared S5 PDF archive: system and wiring documents. Match the full order number and document edition before using a manual.

Related topics

+ About Siemens S5 PLC · S5 cables and connectors · S5 interface modules.

Browse SIMATIC S5

S5 digital input modules | SIMATIC S5 | Siemens S5 PLC | Siemens second-hand main page

Siemens and external references

+ Siemens U-range peripheral manual – Russian: 6ES5998-0PC01-1C; digital I/O section C79000-B8556-C312-04, §5.2, printed pages 4-36–4-37; PDF pages 168–169. Exact 6ES5430-4UA11 specification and connection drawing.

+ Siemens revision transition records: note 4175338 in the 4UA12 product page lists the 4U.11 → 4U.12 transition and the 430-4UA11 order number.