6ES5 421-8MA11

Siemens 6ES5 421-8MA11 – 8-Channel 24 V DC Digital Input Module

Siemens 6ES5 421-8MA11 is an 8-channel, 24 V DC, non-isolated digital input module in the SIMATIC S5 range for S5-100U and ET 100U configurations. It passes switch and sensor states to the control program, with one bit representing each channel.

Check the sensor’s output circuit, supply and reference together. When choosing an inductive sensor or photoelectric sensor, confirm that its output provides the positive signal required by the input; a “24 V” marking alone is insufficient. Include the off-state behaviour of two-wire sensors in the checks.

Common M reference on non-isolated inputs

Non-floating means that the inputs are not galvanically isolated from the controller side. Connect the field and control circuits to the correct M reference. When checking the power supply and S5 supply arrangement, include loose connections and voltage drop in the return path.

The module uses the connections on its compatible bus unit. Inspect S5 cables and connection hardware for corrosion, loose terminals and damaged contacts. Replacing the electronic module will not repair a poor connection in the bus unit; establish which component is responsible before replacing parts.

S5-100U addressing example

In an S5-100U, a digital address combines the slot number and channel bit. Siemens’ example explicitly names the 8MA11 and gives slot 3, channel 1 → 3.1, monitored as I3.1 in English STEP 5 notation or E3.1 in German notation. When reviewing the Siemens S5 PLC architecture, use the front-panel assignment to distinguish terminal numbers from channel bits.

If the module is moved to another slot, check the address read by the program again. Include the S5 interface modules when expansion units are present. During PLC troubleshooting, follow the signal from its field voltage to the input bit and then to the program logic that uses it.

Signal reading and application limits

This module collects on/off information. Keep the distinction between analog and digital inputs: it cannot turn a 0–10 V or 4–20 mA measurement signal into an analog process value. For short or fast pulses, assess pulse duration, input behaviour and CPU scan time together, and consider suitable S5 function modules where required.

8MA11 revision and related modules

6ES5 421-8MA11 and 6ES5 421-8MA12 are different order numbers. Compare the label, front connections and existing hardware list before making a replacement. Do not treat the 6ES5 420-8MA11, 6ES5 422-8MA11 or 6ES5 431-8MA11 as identical because they look similar; check the channel arrangement and isolation requirements separately.

Distinguishing input and output modules

The 421-8MA11 receives sensor information. Relays, lamps and other loads require suitable S5 digital output modules. The 6ES5 441-8MA11 and 6ES5 451-8MA11 belong to that separate group. Specify the complete order number and function when requesting a spare, rather than simply asking for an eight-channel S5 module.

Editor’s Note

Start with the common M connection. Power at the sensor does not settle the condition of the input circuit. A loose return connection can affect several channels and send you looking for faults in the wrong place.

Give all eight inputs a proper check. Switch each channel on and off separately and confirm that the correct PLC bit changes. A few working indicators are encouraging, but they do not prove the remaining channels.

Remember the bus unit underneath the module. Check the terminals, contacts and mechanical seating before condemning the electronics. If reseating the module clears the fault, investigate the connection; a temporary improvement is not a completed repair.

When changing slots, record the old slot, new slot and input addresses in use. The sensor and module may both work while the program waits for a different bit. Checking the address first can save an unnecessary replacement.

For a used module, ask for clear photographs of the full label, front cover and rear contacts. Confirm the 8MA11 suffix, signs of corrosion or overheating, and an eight-channel test result. If it will run with a two-wire sensor, check its off-state behaviour before it goes back into the cabinet.

OtomasyonAVM resources and PDFs

+ Siemens S5 digital input modules and the SIMATIC S5 main directory: related modules and system pages.

+ OtomasyonAVM shared S5 PDF archive: wiring and system documents. Check the full model coverage before using a manual.

Related topics

+ Analog versus digital inputs · PLC input troubleshooting · S5 cables and connectors.

Browse SIMATIC S5

S5 digital input modules | S5 module directory | SIMATIC S5 | Siemens S5 PLC | Siemens second-hand main page

Siemens and external references

+ Siemens 6ES5421-8MA11 product sheet – English: exact order number, eight inputs, 24 V DC and non-floating construction; Siemens document copy hosted by SPS-Service.

+ Siemens S5-100U system manual – English: EWA 4NEB 812 6120-02b; §3.3.3 for the common reference arrangement; §6.2, printed page 6-4, for the addressing example explicitly naming 421-8MA11.