6ES5 420-5AA11

Siemens 6ES5 420-5AA11 – 32-Channel 24 V DC Digital Input Module

Siemens 6ES5 420-5AA11 is a 32-channel, 24 V DC, non-isolated digital input module for S5-130A and S5-150A controllers in the SIMATIC S5 family. Siemens lists it in the Robustbauform, or rugged A-version construction, of Catalog ST 53. Within the S5 digital input module range, it provides four input bytes, approximately 5 mA input current and a typical 3 ms input delay.

The module reads switching signals from inductive sensors, photoelectric sensors and mechanical limit switches. Its thirty-two inputs are arranged as four groups of eight bits. The 5AA11 suffix identifies a particular mechanical and system version; the 420 designation or 24 V rating alone does not establish interchangeability with another S5 input module.

Input voltage and sensor interface

The nominal signal voltage is 24 V DC. The specified logic-1 range is +13 to +33 V; logic 0 is specified as −33 to +4.5 V or an open input. The region between +4.5 V and +13 V is not a defined logic state. The positive switching arrangement makes the difference between PNP and NPN sensors relevant. Check the field power supply together with the input reference.

The module has no galvanic isolation. Signals arriving from different cabinets require attention to common reference connections and potential differences. Typical current at logic 1 is 5 mA per input. This is a digital input module; it does not convert a 0–10 V or 4–20 mA signal into an analog measurement value.

Siemens specifies a typical 3 ms input delay for the 420-5. PLC scan time and program execution add to the overall response time. Catalog cable limits are 400 m unshielded and 1000 m shielded. These limits are not a guarantee for every installation: voltage drop, cable routing and the electromagnetic environment must also be assessed.

A-version construction and four-byte wiring arrangement

The rugged A-version module must not be assumed to share the mechanical or field connection arrangement of a compact module. When checking the S5 rack and carrier, inspect the installed chassis and wiring arrangement. Match the mounting position in the SIMATIC S5 system to the 420-5 connection drawing; do not transfer a compact module’s front-connector part number to this version.

The Siemens drawing assigns inputs 1–8 to byte 0, 9–16 to byte 1, 17–24 to byte 2 and 25–32 to byte 3. Bits run from 0 to 7 within each byte. Input 1 therefore corresponds to bit 0 of the first byte, while input 8 corresponds to bit 7. Use the same drawing for the reference and L-marked connections; Siemens also indicates the relationship between L− and the module carrier.

Addressing and commissioning checks

The thirty-two inputs are represented by four input bytes. For example, if an installation assigns start byte 32, the inputs can be monitored as I32.0–I32.7, I33.0–I33.7, I34.0–I34.7 and I35.0–I35.7. This illustrates the addressing principle; verify the actual start address in the installed system. When reviewing the Siemens S5 PLC architecture, record how the used input module maps to the existing program.

Differences from other 420 and 430 modules

The 6ES5 420-3BA11 uses compact K-version construction. The 6ES5 420-7LA11 belongs to the S5-115U group, while the 6ES5 420-8MA11 is a four-input compact module. Sharing the 420 number does not mean that these modules fit the same chassis or work with the existing wiring.

Where isolation is required, the rugged 6ES5 430-6AA11 is a relevant technical comparison. The 6ES5 430-3BA11 instead uses compact K-version construction. Matching channel count and nominal voltage is insufficient to establish a direct replacement; isolation, construction and connections must also match the application.

This module reads inputs and does not drive loads. When reviewing the output side of an A-version system, consider output modules such as 6ES5 441-5AA12, 6ES5 444-5AA11 and 6ES5 451-5AA13 separately. A correctly detected input only produces machine action when the program conditions and output circuit also operate correctly.

The catalog lists 150 mA from the internal 5 V supply under its (Ityp + Imax) / 2 current definition. This figure must therefore not be treated as a guaranteed maximum current requirement. Listed weight is approximately 0.3 kg. Before purchase, check the complete order number, connection hardware and the results of testing all thirty-two channels.

Editor’s note

Begin with the label and construction. A 420-5AA11 belongs to the A-version installation. Another card marked 420 is not automatically a replacement; check the mounting and connections before deciding.

One working channel does not prove that all thirty-two work. Test each of the four bytes. Pay particular attention to the transitions between inputs 8–9, 16–17 and 24–25, where a shifted wire or incorrect byte assignment becomes easier to spot.

Give the common reference proper attention. Seeing voltage at a sensor output is not enough to condemn a non-isolated input card. Measure the signal against the module’s own reference and inspect return connections before replacing the electronics.

Know what an open input means to the program. An open circuit falls within the logic-0 definition. That state alone does not distinguish a deliberately open contact from a broken wire, so include the field cable in fault tracing.

Photograph the wiring and back up the program before removal. Record the start address, all four input bytes and the existing reference connections. Keep bench testing separate from machine movement, and ask for the unit’s working or faulty status and the exact test coverage.

OtomasyonAVM resources and PDFs

+ Siemens S5 PLC main page

+ S5 digital input modules

+ S5 PDF files — shared manual archive

Related topics

+ 420-3BA11 compact K input module

+ 430-6AA11 isolated rugged input module

+ PNP and NPN sensor comparison

Browse SIMATIC S5

+ S5 digital input modules

+ SIMATIC S5

+ Siemens second-hand main page

+ Used digital input modules

Siemens and external references

+ Siemens ST 53, 1985 — S5-130/S5-150 catalog, German archive copy; specifications 8/5, wiring 8/20, complete order number 9/6