6ES5 135-3UA21

Siemens 6ES5 135-3UA21 — SIMATIC S5-135U Central Rack

The Siemens 6ES5 135-3UA21 is a 21-slot central controller rack (CC) for the S5-135U in the SIMATIC S5 range. Its backplane connects the CPU, I/O cards and interface modules. This S5 central rack includes a fan-cooled power supply and a compartment for the backup battery.

6ES5 955-3LF12 power supply

Siemens specifies the 6ES5 955-3LF12 power supply for this order number. The input is selectable between 120 and 230 V AC, with 230 V AC as the factory setting. The main output is in the 5 V DC / 40 A class, with 5.1 V DC listed as the rated value in the detailed specification. When selecting an S5 power supply, check both the rack and fitted supply nameplates.

The 24 V and optional 15 V auxiliary outputs share a 2.8 A total limit. The front-panel 24 V output has its own 0.4 A nominal rating and counts toward that total. Siemens specifies the 15 V supplementary module in the power supply for configurations with a CP 535 or CP 143 communications processor.

Distinguishing related racks

The 6ES5 188-3UA22 is also in the 5 V / 40 A class. Siemens pairs that rack with the 6ES5 955-3LF42. The 6ES5 188-3UA12 uses the 955-3LC42 with AC input and an 18 A output. The 6ES5 188-3UA32 uses the 955-3NC42 with 24 V DC input and an 18 A output. Match the rack code, power supply code and input voltage when choosing a replacement.

CPU, slot assignments and expansion

The Siemens manual documents the CPU 921 S processor and CPU 922 R processor for this S5-135U configuration. Check the full order number when selecting S5 processors and function modules. Select the memory submodule and programming cable for the fitted CPU. Back up the STEP 5 program before replacing the rack.

Record the slot and address settings before transferring digital input, digital output or analog I/O cards. Use the Siemens slot table to verify the position, supply and signals required by each card.

Siemens shows different interface pairings for the EU 183U and EU 184U in its centralized expansion example. The EU 184U example uses the 6ES5 300-5CA11 at the central rack. Record the interface codes at both ends and the connection order before moving the system.

Buying a used rack

Ask for separate photographs of the rack and power supply nameplates. Inspect the backplane contacts, card guides, locking rail, fans and battery compartment. Confirm whether the CPU, memory and battery are included. Have the voltage selector and protective earth connection checked against the manual before connecting mains power.

Editor’s Note
Ask for a bench test record that shows both the voltage and the load current on the 5 V rail. Siemens specifies a minimum 2 A load on that rail for the 955-3LF12. The record should also show fan operation and CPU access to a known-good I/O card.

PDF archive

In the Siemens central controller instructions, see Table 1 for power supply pairings, Table 2 for slot assignments, §4.1 for minimum load and §6.2 for the 955-3LF12 specifications. Shared Siemens SIMATIC S5 PDF archive

Related topics

About Siemens S5 PLCs · S5 interface modules

Navigation · S5 central units and CPUs · Siemens SIMATIC S5 PLC · Used Siemens automation equipment

References

Siemens S5-135U CPU 921 / CPU 922 Manual, 6ES5998-0UL22, central controller section C79000-B8576-C395-01 (EN)
Siemens S5-135U/155U System Manual, C79000-G8576-C199-07, 188 series comparison (EN)