6ES5 581-0RA12
Siemens 6ES5 581-0RA12 – CP 581 AT/ISA Expansion Slot Module
Siemens 6ES5 581-0RA12 is the AT slot module used to add a short AT/ISA expansion card to a CP 581 assembly in a SIMATIC S5 system. It has a 128-pin X10 internal connection and a 98-contact AT card connector. Its front panel is approximately 20 mm wide and its weight is approximately 0.3 kg. Within the S5 expansion equipment range, it provides the CP 581’s AT expansion slot.
The module has no direct connection to the S5 backplane bus and no backplane connector. It connects to a CP 581 basic board, mass storage module or another AT slot module. Its application within a SIMATIC S5 system depends on the installed AT card and its software; the 0RA12 alone does not define a communication protocol or field I/O channel count.
Basic board, storage module and slot module
6ES5 581-0ED13 and 6ES5 581-0ED14 are CP 581 basic boards. The 0RA12 provides an expansion slot rather than replacing the processor board. When servicing an older assembly containing a 6ES5 581-0EA11 or 6ES5 581-0EC12, record its exact order number and revision instead of selecting parts by the CP 581 family name alone.
6ES5 581-3LA11 and 6ES5 581-4LA11 are mass storage modules. Other storage versions, such as 6ES5 581-5LA11 and 6ES5 581-6LA11, require their own version documentation. Their order numbers identify a different function from the AT slot module.
Installation, connectors and module count
A CP 581 system can operate a maximum of two AT slot modules simultaneously. The Siemens manual illustrates mounting on the basic board or mass storage module. Available space in an S5 rack is only one requirement; assembly width, fixing hardware and cooling must also be suitable.
For a system using a carrier such as 6ES5 185-3UA11, compare the CP 581 installation with the applicable assembly drawing. The X10 connection must be fully seated and the boards secured with the correct spacers. As the slot module has no front-panel communication port, identify which installed board provides any function accessed through S5 interface equipment or connecting cables.
Power supply and cooling limits
The slot module requires +5 V, ±5% and typically consumes 0.3 A without an AT card. The expansion card adds to this load. Assess the complete CP 581 assembly when checking the S5 power supply; an unloaded voltage reading alone does not establish the suitability of a PLC power supply module.
The combined 5 V supply load of two AT slot modules must not exceed 6 A. The manual also specifies a 20 W limit per slot module, reduced to 7.5 W without forced ventilation. Other AT bus voltages are generated from the 5 V supply, so adding only the expansion cards’ 5 V currents is insufficient; use the manual’s load calculation.
S1 switch and expansion-card resources
All six S1 switches are factory-set to OFF. Setting switch 1 to ON disables the I/O address range above 32K on the 0RA12. ON is not a permitted setting for switches 2–6. Do not copy settings from a 6ES5 581-0RA11 without checking the table for the exact module.
Match the installed AT card’s I/O address, IRQ and any DMA settings to its own documentation. Preserve the CP 581 configuration and stored memory contents, and change one setting at a time during diagnosis. Recording the installed card and its settings makes subsequent Siemens S5 maintenance more straightforward.
Editor’s Note
Before buying, establish whether the offer includes the slot module alone or the fitted AT card as well. A card visible in a photograph may not be included. With used Siemens equipment, ask the seller to identify each supplied component.
Inspect the X10 pins and AT connector. Bent pins, cracked plastic and signs of forced insertion deserve closer examination. A clean front panel says little about the condition of the internal connection.
Photograph the S1 settings before removal. Avoid changing switches at random during troubleshooting; ON is not permitted for switches 2–6. Record the expansion card’s own switches separately.
If operation becomes unreliable after warm-up, check supply loading and airflow as well as the connectors. A load requiring fan cooling can make a sound component appear faulty when tested without the required ventilation.
Where possible, test with the intended basic board and the same AT expansion card. A successful CP 581 startup does not prove that the expansion card works through the slot module. Remove power before handling the assembly, secure it correctly and then test the required function.
OtomasyonAVM resources and PDFs
Start with S5 expansion equipment, racks and carriers and the SIMATIC S5 overview. The OtomasyonAVM S5 PDF archive provides a starting point for documents. The technical reference for this module is the English CP 581 User Manual, 6ES5 998-2AT22. Section 2.7 covers assembly, Section 3.3 describes the AT slot module and Section 4.3 gives its electrical and thermal limits.
Related topics
+ CP 581 basic board 0ED14 · CP 581 mass storage module 4LA11 · AT slot module 0RA11 · S5 power supplies
Browse SIMATIC S5
+ S5 expansion equipment · S5 racks · SIMATIC S5 · Used Siemens overview
Siemens and external references
Siemens CP 581 User Manual — 6ES5 998-2AT22, C79000-G8576-C781-02, English