6ES5 454-5AA11

Siemens 6ES5 454-5AA11 — 8-Channel Digital Output Module

Siemens 6ES5 454-5AA11 is an 8-channel digital output module in the 454-5 family for SIMATIC S5 systems. Siemens ST 53 describes the 454-5 family with 24 V DC, a nominal 2 A per channel and isolated outputs. When assessing this older member of the S5 digital output range, check its complete order number together with the existing cabinet wiring.

Assess the outputs for DC control loads within their applicable ratings. For a connected relay or coil, check operating and pickup current. Size the power supply for simultaneously operating loads; the channel rating does not establish that every output may operate at full load simultaneously.

Rack and wiring arrangement

The Siemens catalog places the 454-5 family in the rugged A-type (Robustbauform) S5-130A/150A arrangement. Record the complete numbers of the installed rack and expansion units such as EG 180 or EG 181. Verify the front connector and wiring against the actual 5AA11 version.

Part-number differences within the 454 family

6ES5 454-4UA11, 6ES5 454-4UA14, 6ES5 454-7LA11 and 6ES5 454-7LB11 are different models within the 454 family. Check channel count, construction and terminal arrangement before considering interchangeability. The 454-5AA12 listed in the 1985 Siemens ST 53 ordering table must also be distinguished from the 454-5AA11 covered here.

Output and load checks

Compare the output command in the PLC program, the module’s status indication and measurements at the load. If feedback is provided through a suitable digital input, check that signal as well. An illuminated status indicator alone does not prove that the load is operating at the correct current.

During troubleshooting, establish whether one channel or the whole module is affected. If analog modules or interface modules in the same rack are also affected, inspect the common supply and connection path. Check grounding, cable shielding and sources of electromagnetic interference as well.

Editor’s note

With an older Siemens S5 system, start with the label. Photograph the 454-5AA11 code, module front and connector side. Ordering only by the description “454 output module” can easily result in a different part arriving.

If an output does not work, check its coil, wiring and supply before condemning the module. Installing a serviceable replacement without finding a faulty load can leave you doing the same job twice.

Do not use the nominal channel current as permission to fully load every output. Check cabinet temperature, cooling and simultaneous loads. Confirm the total load limit in the documentation for the actual version.

Back up the program and record the RAM/EPROM memory arrangement, slot address and cable markings before removal. Isolate the supply and verify that the equipment is de-energized. A clear photograph taken beforehand is a valuable companion when working on an old cabinet.

For used Siemens equipment, test all eight outputs with suitable loads where possible. Inspect the front connector for discoloration, the heatsink for looseness and the board for previous repairs. A clear record of the operating test matters as much as a clean appearance.

OtomasyonAVM resources and PDFs

+ OtomasyonAVM S5 PDF archive

+ S5 digital output modules · S5 cables and connectors

Related topics

+ 6ES5 454-4UA11 — different construction and wiring

+ 6ES5 454-4UA14 — another 454 version

+ 6ES5 454-7LA11 — different rack family

+ 6ES5 454-7LB11 — a different eight-channel model

Browse SIMATIC S5

+ S5 digital output modules

+ S5 power supplies

+ S5 mounting racks

+ SIMATIC S5 overview

+ Used Siemens equipment

Siemens and external references

+ Siemens ST 53, 1985 — German; pp. 8/7 and 8/21: 454-5 family specifications and wiring. The ordering table on p. 9/6 lists version 5AA12; this is a family reference.

+ Siemens front-panel label — product photograph showing the exact 6ES5454-5AA11 code; Maranos archive image