6ES7 193-0CA40-0XA0
Siemens 6ES7 193-0CA40-0XA0 – ET 200B TB3-4/DC Spring Terminal Block
Siemens 6ES7 193-0CA40-0XA0 is the TB3-4/DC terminal block for the SIMATIC ET 200B distributed I/O system. Designed for digital electronics blocks, it provides a four-tier spring terminal arrangement for field wiring and supply connections. The specified width is 160 mm.
Within a Siemens ET 200 system, the terminal base and the electronics block perform complementary jobs. The TB3-4/DC carries the wiring connections, while the fitted electronics determine input processing, output operation and channel characteristics. Selecting an ET 200 terminal block therefore starts with identifying the electronics already installed.
Technical specifications and operating conditions
The Siemens data sheet for this order number specifies a 24 V DC rated supply and a permissible range of 18.5–30 V DC, including ripple. Listed current consumption is 100 mA typical and 170 mA maximum. These figures should not be treated as the available current for connected output loads; load capacity must be checked against the electronics block.
Published dimensions are 160 × 130 × 59 mm (width × height × depth), with an approximate weight of 600 g and an IP20 protection rating. The ET 200B manual permits 0 to +60 °C for horizontal installation on a vertical surface and 0 to +40 °C in other mounting positions. Cabinet planning should also allow room for cables and removal of the electronics block.
Compatible electronics blocks
Siemens identifies the following compatible units: ET 200B-16DI, ET 200B-16DO, ET 200B-8DI/8DO, ET 200B-8DI/8DO HWA and ET 200B-8RO. With the appropriate electronics, the base can serve digital input, digital output, mixed I/O or relay output applications.
The TB3-4/DC follows the functionality and terminal assignments of the four-tier TB1-4/DC, using spring connections in place of screw terminals. The “4” describes the four-tier terminal layout. The electronics block remains the reference for channel count and electrical performance.
Terminal tiers and protective earth connections
Read the terminal arrangement against the wiring diagram for the fitted electronics. Treating every connection as an independent signal terminal can lead to mistakes involving shared supplies and reference potentials. When connecting a sensor or an inductive sensor, identify its signal, supply and reference connections individually. Its output type must also suit the selected input electronics.
The fourth-tier PE terminals are interconnected, but they are not internally connected to the terminal block’s PE screw. This distinction matters when arranging protective earth wiring in the cabinet. A wire landed on a PE-marked terminal does not, by itself, establish the complete protective earth path.
PROFIBUS connection and station settings
The TB3-4/DC includes the PROFIBUS-DP connection, station address setting and STOP/RUN switch. A changed station address is accepted following a STOP-to-RUN transition. During commissioning, check that the physical address matches the station configured in the PLC project.
Communication troubleshooting should cover the cable, connector, bus termination and project settings as well as the terminal base. The guides to PROFIBUS communication and PROFIBUS and PROFINET in ET 200 systems provide useful background when working across different station generations. This particular terminal block uses PROFIBUS-DP.
Power supply and cabinet installation
Select the power supply using the combined requirements of the station electronics, sensors and output loads. A DIN rail power supply needs sufficient current capacity, while the voltage must remain suitable at the station terminals under load. Arrange the supply groups according to the wiring diagram for the fitted electronics.
The base supports mounting on a 35 × 7.5 mm or 35 × 15 mm DIN rail, or directly on a suitable flat surface. Leave enough space around cable ducts to avoid pulling on the terminals and to permit access during maintenance. When reviewing power distribution modules and ET 200 power supply components, check the connection requirements of the specific ET 200 family.
Maintenance and replacement checks
For intermittent channel faults, useful inspection points include conductor retention, wire-end condition, corrosion and the contacts between the terminal base and electronics block. A complete station dropout also calls for checks on supply and communication. Recording when the fault occurs helps avoid replacing the base while leaving the underlying problem unresolved.
Before selecting a replacement, record 6ES7193-0CA40-0XA0, the TB3-4/DC designation and the full order number of the electronics block. Inspect the housing, spring terminals, mechanical retention and connector area. Perform wiring work with the relevant supplies isolated; the STOP position alone does not establish that all field circuits are de-energized.
Manuals and wiring information
Use the ET 200B Distributed I/O Station manual together with product information supplement EWA 4NEB 780 6731-02 when checking terminal assignments. Visit the Siemens ET 200 manuals and PDF documentation page for the documentation collection. Match the wiring information to both the terminal block and the complete electronics order number and version.
Editor’s note: Evaluate the TB3-4/DC four-tier spring terminal arrangement against the existing cabinet wiring. Small changes in an order number can identify a different terminal design, housing size or compatible electronics group. Use the equipment labels and the manufacturer’s wiring diagram together when selecting a replacement.
Related topics
Explore ET 200 connection modules and ET 200 additional modules for other connection and accessory options. These pages cover several ET 200 families, so compatibility must be checked for each individual model.
Navigation
Siemens products | Siemens S7 PLC | SIMATIC S7 | Siemens ET 200