6ES7 194-1AA00-0XA0

6ES7 194-1AA00-0XA0 – Siemens ET 200X PROFIBUS and power supply connector

6ES7 194-1AA00-0XA0 is a connector for PROFIBUS DP and power supply cables in the Siemens ET 200X system. It is listed among the connection accessories for earlier BM 141 and BM 142 basic modules. Check the complete order number, basic-module revision, cable gland and completeness of the assembly when selecting a part. See the ET 200 system overview for family context.

Related basic modules

The Siemens ST 40 catalog lists AA00 in the accessory arrangement for earlier ET 200X basic modules such as 6ES7 141-1BF01-0XB0 BM 141 and 6ES7 142-1BD11-0XB0 BM 142. Read the complete code on the installed device, including its suffix; similar order numbers can identify different connection arrangements.

Connector construction and assembly contents

Siemens AA00 wiring drawings show a six-pole arrangement with screw terminals. The ST 40 catalog describes the assembly as including two cable glands and one blanking plug. For a used item, confirm the presence of the body, contact insert, glands, seal and blanking plug from photographs. Also check the supplied components when browsing other ET 200 connection parts.

Distinguishing AA00 from AA01

The 01/1999 MOBY V manual describes the PROFIBUS/supply connection using AA00 as PG11. In the 02/2003 ET 200X manual, 6ES7 194-1AA01-0XA0 is listed with M16 cable glands. When considering replacement, check the gland thread, clamping range for the cable diameter and fit with the housing. Similar order numbers alone do not establish replacement suitability.

Cable selection and wiring checks

6ES7 194-1LY00-0AA0 is the standard five-core, PVC-sheathed cable listed for ET 200X bus signals and power supply. Consider conductor construction, outside diameter, shield connection and fixed or moving installation requirements when selecting the cable. Prepare the conductors according to the connected device’s own terminal diagram.

AA00 also appears in Siemens documentation for ASM 451/452. On those devices, the supply must be connected separately through X13, while the optional supply contacts in the PROFIBUS plugs remain unwired. This instruction applies to ASM 451/452 and should not be transferred directly to another device using the same connector.

Protection and mechanical condition

The ASM 451/452 manual requires all three plugs to be fitted, wired or unwired, to maintain the stated IP65/IP66/IP67 protection. This is an installation condition for the assembled device, not a three-piece sales package. Loose contacts, cracked housings, worn seals and missing blanking plugs require closer inspection than an external appearance check.

Addressing and station checks

AA00 provides the cable connection. 6ES7 194-1KB00-0XA0 serves as an address-setting plug in supported DESINA/ECOFAST arrangements. See the PROFIBUS FAQ for network addressing and termination background.

Communication troubleshooting should consider contact integrity, shield continuity, the power supply and PLC configuration together. Browse ET 200 PROFIBUS and PROFINET and network interfaces when reviewing system options.

Editor’s Note: Before disconnecting the old cable, photograph terminal numbers and connection positions. During replacement, check the number, terminal function and device diagram together instead of relying only on conductor colors. Photographs of the internal contacts and cable entries provide more useful evidence when buying a used connector than a closed-housing photograph alone.

Manuals and PDF documents

Relevant documents are available through the Siemens ET 200 manuals section. AA00 and the cable are listed on ST 40 page 4/38; PG11 is specified on MOBY V page 6-34; ASM 451/452 wiring conditions appear on FC 46 pages 2-5–2-6. Use page A-3 of the 02/2003 ET 200X manual for the AA01 comparison.

Related topics

Browse industrial communication, PLC and HMI and Siemens S7-300 for other system components.

Navigation

Siemens ET 200 | Siemens SIMATIC S7 | Siemens automation | OtomasyonAVM home