6ES7 134-4JB01-0AB0

6ES7 134-4JB01-0AB0 – Siemens ET 200S 2AI TC Standard

6ES7 134-4JB01-0AB0 is a two-channel thermocouple and millivolt input module for Siemens ET 200S. Designated 2AI TC Standard, this 15 mm wide electronic module transfers thermocouple signals to the control system. Check sensor types and measuring ranges when choosing a probe from the temperature sensors section.

Thermocouple types and measuring range

Supported thermocouples are types B, E, J, K, L, N, R, S and T. The module also provides ±80 mV voltage measurement. Resolution is specified as 15 bits plus sign. The thermocouple type selected for the channel must match the installed probe and compensating cable.

Cold-junction compensation

This module does not support internal cold-junction compensation. An external compensating box can be used for each channel, or the reference temperature can be measured by a Pt100 connected to an RTD module in the same ET 200S station. The Pt100 connects to that separate RTD module’s input.

For RTD compensation, select the Pt100 Climatic range and coordinate the reference settings of the RTD, thermocouple and interface modules. Siemens recommends a four-wire Pt100 connection and good thermal contact with the reference junction. When both thermocouple channels use RTD compensation, they share the same reference channel.

Terminal connections and supply

Suitable terminal module examples include TM-E15S23-01 and TM-E15S24-01. When selecting connection components, check the complete terminal code, thermocouple polarity and shield connection.

The nominal 24 V DC load supply comes through the ET 200S power module. The inputs are isolated from the backplane bus and load supply; there is no galvanic isolation between channels.

Station and network connection

The interface module provides the station’s network connection. IM 151-1 High Feature is a PROFIBUS example, while IM 151-3 PN High Feature is a PROFINET example. Compare the network arrangement, interface revision and reference-temperature assignment with the existing project. Browse ET 200 analog and interface modules for other options.

Conversion time and diagnostics

Basic conversion takes 55 ms per channel with 60 Hz interference suppression or 65 ms with 50 Hz suppression. Enabling the wire-break check adds 20 ms. The module cycle depends on the active channel count and conversion time.

The red SF LED indicates a group fault. Group, underflow/overflow and wire-break diagnostics are disabled by default. The wire-break check is available only for thermocouple measurement. Enabling it in the ±80 mV voltage range causes a parameter error and prevents the module from starting.

Related models and replacement checks

6ES7 134-4NB00-0AB0 is a High Feature thermocouple module, while 6ES7 134-4JB50-0AB0 handles RTD and resistance inputs. Evaluate the measurement type and compensation arrangement alongside the complete order number.

The Siemens manual states that JB01 is compatible with 6ES7 134-4JB00-0AB0. Before replacement, record the hardware configuration, terminal arrangement and reference settings, and verify the match with the existing project.

For a used unit, inspect the contacts, mechanical latches and nameplate. Request a test record showing the thermocouple type, reference temperature and measurement points used to check both channels.

Editor’s Note: Before correcting a persistent temperature offset in software, check the thermocouple type, polarity and cold-junction reference. The test record should include the displayed temperature together with the calibrator’s thermocouple type and compensation setting. This makes the conditions under which the measurement chain was checked clear.

Manuals and PDF documents

Documentation is available through the Siemens ET 200 manuals section. In this model’s 05/2012 manual, A5E01076883-03, pages 7–13 cover technical data and parameters, 29–33 explain thermocouple connections and compensation, and page 34 covers wiring unused channels.

Related topics

Browse temperature controllers for temperature applications, and PLC and HMI, PLCs and modules and Siemens S7-300 for other control-system components.

Navigation

Siemens ET 200 | Siemens SIMATIC S7 | Siemens automation | OtomasyonAVM home