6ES7 127-1BE00-0AB0
6ES7 127-1BE00-0AB0 — Siemens SIMATIC SC 1COUNT40kHz
Series: Siemens SIMATIC SC / Smart Connect. Category: Counter module for ET 200L-SC IM-SC in the ET 200 family.
6ES7 127-1BE00-0AB0 is a single-channel 40 kHz counter module accepting 24 V DC pulse and direction signals. Applications include counting pulses from a photoelectric or proximity sensor. Counting takes place in the module, while the PLC reads the count and sends control commands.
System compatibility and terminal block
The supported platform is ET 200L-SC IM-SC. The module can be used on TB 16IM-SC or on a TB 16SC expansion connected to that system. The names “ET 200L” or “Smart Connect” alone are insufficient to establish compatibility. Check the terminal block, interface and existing hardware configuration together.
The counter connects to the station through the SC bus; the station’s IM-SC interface handles PROFIBUS communication. There is no network cable connection on the counter itself. Selecting one of the other network interfaces during an upgrade does not establish mechanical or software compatibility with this module.
Electrical and physical specifications
The nominal supply is 24 V DC, no-load consumption is approximately 20 mA, and maximum power loss is 0.5 W. Dimensions are 10 × 64 × 51 mm, with an approximate weight of 15 g. Include sensor consumption separately when assessing the power supply and power distribution.
The count input accepts −3 to +5 V as low and +11 to +30 V as high; typical high-level input current is 6 mA. Maximum counting frequency is 40 kHz, with a minimum pulse width of 12.5 µs. The Siemens manual specifies a maximum 100 m shielded cable. Two-wire sensors must have a quiescent current no higher than 1.5 mA.
Pulse and direction wiring
The local connections are 1/A: count pulse, 2/L+: positive supply, 3/B: direction signal, and 4/M: supply reference. The terminal block’s letter identifies the slot; for example, slot A uses A1–A4. When checking connection components, distinguish these local terminal identifiers from the cabinet’s wire numbers.
A and B serve as pulse and direction inputs. Their names do not identify a two-phase quadrature encoder interface. In up/down mode, B=0 selects upward counting and B=1 selects downward counting. Up-only mode ignores the direction input. Connecting the same sensor to standard digital inputs does not establish equivalent counting performance.
Counting modes and PLC data exchange
The counter uses an unsigned 16-bit value, with lower and upper limit parameters adjustable within 0–65535. It supports continuous, single-pass and periodic counting. A PLC-controlled gate starts and stops pulse accumulation. The interface occupies 6 input bytes and 6 output bytes, carrying count, status, load and comparison information.
Siemens’ December 2004 supplementary information clarifies that, during continuous upward counting, the pulse after upper-limit-minus-one returns the counter to its lower limit. With a lower limit of 0 and upper limit of 100, for example, the displayed sequence is 0…99. The upper limit parameter should therefore not be treated as the final displayed count.
Comparison result and operating checks
The comparison result is a status bit; the module has no physical control output. To operate a load, the PLC must read that bit and transfer it to a suitable digital output. Communication and program execution add to the response time. A 40 kHz counting capability therefore does not mean that a physical output can be switched at the same rate.
Editor’s note: If pulses are present but the value remains unchanged, check the gate enable, valid control command and data addresses first. For reversed counting, inspect both the direction input and the selected counting mode. Apply a known number of pulses, compare the result, then test the limit transition. An illuminated LED alone does not verify the entire counting chain.
PDF documentation and manuals
Use the product data sheet together with Chapter 13 of the ET 200L, ET 200L-SC and ET 200L-SC IM-SC manual. The December 2004 product information supplement also matters for limit behavior and control data. See the Siemens ET 200 PDF and user manuals page for documentation.
Related topics
Explore ET 200 system structure, function modules, positioning modules and additional modules when assessing other application requirements. Safety modules and PROFIsafe involve separate system requirements. These category links do not establish that listed components fit the existing SC slot.
Navigation: Siemens automation > Siemens S7 PLC > SIMATIC S7 > Siemens ET 200