6ES7 141-4BF00-0AB0
Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7141-4BF00-0AB0
Siemens 6ES7 141-4BF00-0AB0 — ET 200pro 8 DI 24 V DC High Feature
The 6ES7 141-4BF00-0AB0 is an ET 200pro High Feature digital input module in the Siemens ET 200 family. It reads eight 24 V DC field signals. Among ET 200 digital input modules, it provides channel diagnostics for sensor-supply short circuits and wire breaks. Siemens specifies that the bus module is included; the I/O connection module is ordered separately.
Input characteristics and sensor selection
Input type: P-reading, detecting a positive signal. “0” level: −3…+5 V; “1” level: +11…+30 V. Compare the sensor's output type with the input's electrical characteristics. A device's 24 V supply rating alone does not establish signal compatibility. Consider ET 200 analog input modules separately for sensors providing continuous measurement values.
HF functions and input delay
Selectable input delay: 0.5 / 3 / 15 / 20 ms; default 3 ms. Rising- or falling-edge hardware interrupts can be configured on channels 0–5. Check whether diagnostics and interrupt functions are enabled in the existing project.
Assess the delay against the shortest genuine signal that must be detected. A very short setting can expose unwanted transitions, while a long setting can cause short events to be missed. When reviewing the ET 200 station configuration, consider sensor response, communication and the PLC program's response together.
Choosing between 4×M12 and 8×M12
CM IO 4×M12: 6ES7194-4CA00-0AA0; CM IO 8×M12: 6ES7194-4CB00-0AA0. The former provides two inputs per socket; the latter provides one. When selecting ET 200 connection modules, consider more than the connector count.
With CM IO 4×M12, short-circuit diagnostics map channels 4–7 to channels 0–3, preventing exact channel identification. If individual sensor fault identification is required, assess the connection arrangement against this limitation. Likewise, ET 200 terminal blocks from other series should not be treated as direct substitutes for these connection modules.
Sensor supply and station connections
Sensor supply: nominal 0.5 A per channel; maximum 1 A total up to 55 °C. Account for all sensors' simultaneous consumption when selecting ET 200 power supply modules and ET 200 power distribution components. Distinguish this sensor supply rating from the load-driving capacity of ET 200 digital output modules.
Five checks before selection or replacement
1. Complete order number: Record 6ES7141-4BF00-0AB0 from the label. Do not assume identical diagnostics and parameter options for the 0AA0 standard version and the HF version.
2. Sensor and cable: Compare sensor output type, supply and connector assignments. Use the sensor's own wiring diagram rather than relying on cable colours.
3. Connection module: Record the CM number and the inputs assigned to each socket. Show cable branches on the drawing, particularly where a socket carries two inputs.
4. Project and communication: Back up the PROFIBUS or PROFINET interface configuration, hardware setup, input delay and interrupt settings. Using the same electronic module does not mean that every station setting is identical.
5. Functional test: After replacement, operate sensors individually. Verify the mapping between each physical sensor, input address and program function, and check diagnostic messages.
Editor's note: HF diagnostics are useful when wiring and parameters are correct. Establish which channel belongs to which socket before investigating a sensor fault. Confusing a wire-break diagnostic with a normal inactive sensor state can lead to unnecessary replacement of working components.
Manuals and PDF documents
Consult the ET 200pro documents on the Siemens ET 200 PDF and user manuals page. A5E00335544-08, section 14.2 covers this model's technical data; section 14.9 explains parameters and the connection-dependent diagnostic limitation.
Related topics
Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules
Explore the station: About ET 200 · Communication interfaces · ET 200 manuals
Otomasyon AVM | Siemens:
Siemens main menu | Siemens S7 PLC | SIMATIC S7 | ET 200 modules