6ES7 131-4CD00-0AB0

6ES7 131-4CD00-0AB0

Series: Siemens SIMATIC DP / ET 200S

Category: ET 200S Digital Input Module – 4DI UC 24–48 V High Feature

Description

6ES7 131-4CD00-0AB0 is a four-channel High Feature digital input module for the Siemens SIMATIC ET 200S distributed I/O system. It acquires status signals from switches and suitable proximity sensors. The designation 24–48 V UC identifies an input design supporting AC or DC voltage within the specified range.

Within the ET 200 family, its 15 mm electronic module width helps build compact stations. Selecting a digital input module requires checking the field voltage, sensor characteristics and diagnostic requirements alongside the channel count.

Device Function and Applications

The module can acquire on/off information from pushbuttons, limit switches and electrically compatible proximity sensors. Machine position, part presence and auxiliary equipment status can then be processed by the connected controller. These field signals become part of the automation system through the station’s I/O configuration.

AC/DC capability does not establish compatibility with every sensor. The sensor output circuit, operating voltage and off-state current must suit the input characteristics. For two-wire electronic sensors, leakage current and wire-break monitoring conditions deserve particular attention.

Technical Specifications

Order number: 6ES7131-4CD00-0AB0
System: SIMATIC ET 200S
Electronic module class: High Feature
Digital inputs: 4 DI
Rated input voltage: 24–48 V AC/DC, UC
AC frequency range: 47–63 Hz
Input delay: Maximum 15 ms for both 0→1 and 1→0 transitions
Group fault indication: Red SF LED
Channel status indication: Green LED for each input
Parameter length: 3 bytes
Electronic module dimensions: 15 × 81 × 52 mm; width × height × depth
Weight: Approximately 35 g
Manufacturer packaging: 5 modules per packaging unit

The five-module figure describes the manufacturer’s packaging unit. Check the individual Otomasyon AVM listing for the actual sales quantity and scope of delivery. The electronic module dimensions should also be distinguished from the complete installation dimensions with its terminal module.

Terminal Module and Connections

6ES7 131-4CD00-0AB0 plugs into a suitable ET 200S terminal module. Options listed in the Siemens manual include the screw-terminal TM-E15S26-A1 / 6ES7193-4CA40-0AA0 and spring-terminal TM-E15C26-A1 / 6ES7193-4CA50-0AA0. Select the terminal block according to the existing wiring and required auxiliary terminals.

Terminal numbering and available auxiliary connections must be checked for the selected base. Compare complete part numbers when selecting connection components. Field connectors, cable joints and terminal contacts should also be inspected when signals disappear intermittently.

Power Supply and Potential Groups

The station’s power infrastructure must suit the field voltage. The input module’s UC designation does not establish that every upstream power module supports AC or 48 V operation. Verify the voltage limits of the selected ET 200 power supply module together with the other devices in the potential group.

If several inputs disappear simultaneously, check the common supply and power distribution arrangement first. Appropriate grounding and cable routing also matter in panels containing contactors and motor cables.

Programming and Data Information

The four input states reach the PLC program through the input addresses assigned in the station configuration. The Siemens data sheet specifies an address space of 4 bits with supported packing or 1 byte without packing. Read the actual addresses from the hardware configuration.

The three-byte parameter length describes parameter data and is separate from the input address space. Select the complete order number in the project and configure diagnostics to match the field circuit. Communication with the controller depends on the station interface; the input module alone does not determine whether PROFIBUS or PROFINET is used. Check the installed interface against the relevant ET 200 communication configuration.

SF Indication and Wire-Break Diagnostics

The green channel LEDs indicate input status, while the red SF LED provides group fault indication. The SF light alone does not identify the defective component. Siemens product information lists wire break, blown fuse and missing load voltage diagnostics. Interpret these using the enabled parameters and station diagnostic records.

Wire-break monitoring requires suitable electrical conditions. The Siemens manual specifies a minimum monitoring current of 0.5 mA with the sensor switched off. If the sensor cannot provide this current, the appropriate resistor circuit described in the manual may be required. With monitoring enabled, unused inputs left open can also produce wire-break indications; handle those inputs according to the documented arrangement.

Maintenance and Commissioning Recommendations

Supply check: First verify the potential group voltage, power module and common connections. Then compare the signal at the relevant input terminal in both sensor states. Select AC or DC measurement appropriately for the actual field supply.

Signal check: Confirm that the channel LED and PLC input bit change together when the sensor changes state. If the LED responds correctly but the program value does not, inspect addressing and hardware configuration. When assessing machine response, include communication and program cycle time alongside input delay.

Module replacement: Compare the complete order number, terminal base and project settings. Another module with the same width or channel count may have different voltage and diagnostic characteristics.

Editor’s Recommendations

A useful maintenance distinction is whether the field signal has actually disappeared or wire-break monitoring is reporting a fault because of the circuit conditions. Checking the supply, sensor off-state current and unused inputs before replacing the module can prevent unnecessary component changes. Also confirm whether the electronic module and terminal base are both included in the order.

Related Topics

Explore ET 200 additional modules, SIMATIC S7 products and the Siemens S7 PLC category for related equipment groups.

+ Siemens ET 200 PLC user manuals (PDF documentation page)

+ Siemens ET 200 product catalogue including 6ES7 131-4CD00-0AB0 (PDF file)

++ Siemens Automation Main Page >

++ Siemens Automation Contact (for Otomasyon AVM)

++ About Siemens ET 200 PLC >

Reminder: Availability, quantity and scope of delivery for Siemens 6ES7 131-4CD00-0AB0 and other SIMATIC PLC modules must be checked against the individual product listing. Some devices are used products; consider their stated condition before purchasing. Products will not be restocked once sold out. This page provides general information; consult the manufacturer’s documentation for definitive specifications and application requirements.

Note: Manuals, commissioning explanations and troubleshooting suggestions on this page are non-binding and may be updated or improved. The Otomasyon AVM Community welcomes practical experience and usage suggestions. Please contact us to share technical observations or corrections.