6ES7 131-1BL00-0XB0
6ES7 131-1BL00-0XB0
Series: Siemens SIMATIC DP / ET 200L
Category: ET 200L Electronic Input Block – 32 DI, 24 V DC, PROFIBUS-DP
Description
6ES7 131-1BL00-0XB0 is a 32-channel digital input electronic block for the Siemens SIMATIC ET 200L distributed I/O system. It acquires nominal 24 V DC field signals and transfers their status through its integrated PROFIBUS-DP connection.
Within the ET 200 family, this product provides a compact station arrangement with numerous inputs collected in one block. When selecting a digital input block, check its terminal base, field supplies and existing project configuration alongside the electronic component.
Device Function and Applications
The block acquires status signals from pushbuttons, limit switches and electrically compatible proximity sensors. Machine position, product presence and auxiliary equipment status can then be evaluated by the PLC program. Clear identification of field devices and their assigned inputs simplifies maintenance of the automation system.
The inputs are arranged in two sections, A and B, with 16 channels each. If several signals within one section disappear together, investigating common supplies and connections before individual sensors can help locate the cause.
Technical Specifications
Order number: 6ES7131-1BL00-0XB0
System: SIMATIC ET 200L
Product type: Electronic input block
Digital inputs: 32 DI
Channel arrangement: 2 × 16 inputs
Rated input voltage: 24 V DC
Signal “1” input range: 13–30 V DC
Signal “0” input range: −30 to +5 V DC
Input current: Typically 5 mA at 24 V
Input delay: 2–4.5 ms in both transition directions
Communication: PROFIBUS-DP
Maximum supported communication rate: 1.5 Mbit/s
Input data: 32 bits, 4 bytes
Indicators: Channel status LEDs, ON and BF
Terminal base: Suitable TB 32L
Electronic block dimensions: 145 × 60 × 60.5 mm; width × height × depth
The input thresholds define the voltages recognized as logic states and should be distinguished from the nominal supply rating. If voltage drop leaves a signal between the defined “0” and “1” regions, inspect the sensor output, cable and connection points together.
PROFIBUS-DP Communication
The electronic block operates as a PROFIBUS-DP slave through its integrated connection. Its station address, device selection in the master project and input data length must agree. General information about PROFIBUS communication helps explain addressing and network wiring.
The address is set using rotary switches on the device. During replacement, compare the original station address with the project and verify that no duplicate address exists on the network. When reviewing broader ET 200 communication options, use this model’s PROFIBUS-DP specification as the basis for compatibility checks.
TB 32L Terminal Base
The 6ES7 131-1BL00-0XB0 electronic block operates with a TB 32L terminal base carrying the field wiring. Siemens lists the screw-terminal 6ES7193-1CL00-0XA0 and spring-terminal 6ES7193-1CL10-0XA0 versions. The appropriate terminal block forms part of the station’s mechanical and electrical arrangement.
The electronic block and terminal base are separate components, so check the listing’s scope of delivery. Poor contact in connection components can interrupt inputs even when the electronics are functioning. Auxiliary terminals and other ET 200 accessories must also suit the installed base.
Electronics Supply and Sensor Supply
The electronics supply and field sensor supply have separate functions in the wiring diagram. When checking the 24 V DC power infrastructure, investigate beyond the ON indicator. The electronics may remain powered while a sensor supply section is missing voltage.
Important for the older 1BL00 version: Siemens specifies a maximum sensor supply load of 5 A per input byte. This is a sensor supply limit, separate from an individual input’s signal current. Terminal, conductor, protective device and total loading limits must be assessed together. Protection details for the later 1BL01 version must not automatically be applied to the older block.
For grouped signal loss, inspect supply distribution, common connections and fuses. Use the correct M reference for measurements and trace the project’s grounding arrangement separately.
Programming and Data Information
The 32 digital inputs produce four bytes of input data. Their starting address depends on the master configuration; physical channel numbering should be mapped to the assigned PLC addresses. The configured device description or GSD file must match the installed electronic block.
During commissioning, operate each field device individually and compare its channel LED with the corresponding input bit. When assessing application response, include PROFIBUS updating and controller program cycle time alongside input delay.
ON, BF and Channel Indicators
The ON indicator monitors the electronics supply, while BF relates to PROFIBUS communication. Channel LEDs indicate input states. When investigating a BF indication, check the station address, master configuration, bus connector, cable and line termination together.
If a channel LED and PLC input value disagree, first check communication and address mapping. If the sensor changes state but its channel LED does not, inspect field voltage, the sensor output, connectors and terminal contacts. Bus diagnostics alone do not establish the integrity of every sensor cable.
Maintenance and Replacement Selection
Before replacement, record the complete order number, TB 32L base, PROFIBUS address and project information. 6ES7131-1BL00-0XB0 and 6ES7131-1BL01-0XB0 are different versions; check their supply and protection details when evaluating compatibility.
Editor’s recommendation: Investigate electronics power, sensor power and PROFIBUS communication separately. Inputs disappearing while ON remains illuminated do not establish an electronic block failure. First verify the affected section’s voltage and terminal contacts, then compare channel LEDs with PLC data.
Related Topics
Explore SIMATIC S7 products and the Siemens S7 PLC category for controllers and related automation equipment.
+ Siemens ET 200 PLC user manuals (PDF documentation page)
+ Siemens ET 200L system manual covering 6ES7 131-1BL00-0XB0 (English PDF; section 8.3)
+ Siemens ET 200 general product catalogue (PDF file; verify the full order number for version-specific information)
++ Siemens Automation Main Page >
++ Siemens Automation Contact (for Otomasyon AVM)
Reminder: Availability, quantity and scope of delivery for Siemens 6ES7 131-1BL00-0XB0 and other SIMATIC PLC modules must be checked against the individual listing. Some devices are used products; consider their stated condition before purchasing. Products will not be restocked once sold out. This page provides general information; consult the manufacturer’s documentation for definitive specifications and application requirements.
Note: Manuals, commissioning explanations and troubleshooting suggestions on this page are non-binding and may be updated or improved. The Otomasyon AVM Community welcomes practical experience. Please contact us to share technical observations or corrections.