6ES7 131-0BH00-0XB0

Siemens 6ES7 131-0BH00-0XB0 – ET 200B 16DI 24 V DC Digital Input Electronics Block

Siemens 6ES7 131-0BH00-0XB0 is a 16-channel, 24 V DC digital input electronics block for the SIMATIC ET 200B distributed I/O system. It transfers signals from sensors, pushbuttons and position switches to the controller through PROFIBUS-DP. Typical applications include maintaining existing ET 200B stations, replacing their electronics and reviewing field-signal arrangements. Explore the Siemens ET 200 family and our ET 200 digital input modules for related products.

A packaging machine may use these inputs for product detection, mechanism positions and auxiliary contact states. Recording the purpose and input assignment of each sensor remains valuable throughout the machine's service life. Knowing what a signal represents helps maintenance staff follow a fault more effectively than a cable number alone.

Electronics Block and Compatible Terminal Bases

Specified terminal options are TB1/DC, TB1-4/DC, TB3/DC and TB3-4/DC. Common examples include 6ES7 193-0CA10-0XA0 TB1/DC, 6ES7 193-0CA20-0XA0 TB1-4/DC and 6ES7 193-0CA30-0XA0 TB3/DC. Choose the connection method and number of terminal tiers to suit the existing wiring. Our ET 200 terminal blocks page provides related options.

Field wiring stays on the terminal base when the electronics are replaced. The PROFIBUS connection and station-address setting are also located on the base. Inspect the base as well as the electronics when planning a replacement: loose connections, damaged contacts or an unsuitable base can allow the original fault to persist.

Input Signals and Sensor Compatibility

The input thresholds are +13 to +30 V for logic “1” and −30 to +5 V for logic “0”. Typical active-input current is 4 mA at 24 V. Two-wire proximity sensors are supported with a maximum quiescent current of 1.5 mA. When changing a sensor, compare its output circuit and off-state leakage as well as its operating voltage.

If a photoelectric sensor indicator disagrees with the state seen by the PLC, measure the voltage at the module input. For signals from a relay or contactor auxiliary contact, check that contact operation actually establishes the required input voltage.

Input Delay and Communication

Input delay is 2–3.5 ms. The specified maximum unshielded sensor-cable length is 100 metres. For brief detection pulses, consider sensor response, input delay, PROFIBUS timing and the PLC scan together. Network speed alone does not determine whether a passing object will be detected reliably.

The module supports PROFIBUS-DP communication up to 12 Mbit/s and the FREEZE function. The actual network rate depends on the master configuration and connected devices. See our PROFIBUS and PROFINET overview for background, or explore ET 200 communication interfaces for related equipment.

Before replacing equipment in an existing station, record the device definition, station address and input mapping. Operation with S5 or S7 systems depends on a suitable PROFIBUS-DP master and project configuration. These details should also be checked when comparing another block with the same input count.

Supply Arrangement and Sensor Current

Electronics and sensor power are supplied through L3+ / M3. The nominal supply is 24 V DC, with a permitted range of 18.5–30.2 V DC. Typical logic consumption is 70 mA, and the specified total sensor-current limit is 500 mA. When adding sensors, assess their combined consumption, power-supply capacity and cable voltage drop together.

If the terminal base's F1 fuse opens, the internal electronics also lose power. A sensor-circuit problem can therefore appear as a complete station failure. When checking the fuse, investigate the cause as well as the failed component. Replacing it alone may leave the original wiring fault unresolved.

The inputs share a potential with the internal electronics, while PROFIBUS is galvanically isolated. Include grounding, shielding and sensor connectors when investigating intermittent faults.

Indicators and Cabinet Installation

Indicators include green RUN, red BF and green input-status LEDs. Treat an inactive channel and a station communication failure as separate conditions. Clear descriptions on the HMI or SCADA display help maintenance staff begin with the relevant checks.

The combined electronics block and terminal base measure 160 × 130 × 60 mm and weigh approximately 600 g. These figures apply to the assembled arrangement. Typical power loss is 2.5 W and protection is IP20. Operating temperature is 0 to +60 °C horizontally and 0 to +40 °C in other mounting orientations. Allow additional cabinet space for cable bends and connector access.

Editor's Recommendation

If all inputs disappear together, check the RUN indicator, L3+ supply, terminal-base STOP/RUN switch and F1 fuse before concluding that the electronics have failed. A shorted sensor cable can affect the shared supply and produce a much broader fault indication. For a replacement enquiry, photographs of both the electronics label and terminal base provide a clearer starting point than the electronics order number alone.

Order Verification and Technical Documentation

Use the complete order number, 6ES7131-0BH00-0XB0, when matching the product. The quotation should identify whether the electronics block, terminal base and PROFIBUS connector are included. Wiring diagrams are provided in section 7.3.1 of the Siemens ET 200B system manual. Our Siemens ET 200 manuals page provides access to further series documentation.

Related Topics

About Siemens ET 200 · ET 200 digital output modules · ET 200 connection modules

Siemens > SIMATIC S7 > ET 200