6ES7 193-4DL00-0AA0
Siemens automation › SIMATIC S7 › Siemens ET 200 › TM-C120C
Siemens 6ES7 193-4DL00-0AA0 — ET 200S COMPACT TM-C120C Terminal Module
The 6ES7 193-4DL00-0AA0 is a TM-C120C terminal base for ET 200S COMPACT modules within the Siemens ET 200 distributed I/O family. It uses spring-loaded terminals. This component in the ET 200 terminal block range carries the compact module's field wiring; it is not a standalone I/O module or PLC.
Terminal arrangement and dimensions
The product has 4 × 21 connection points and is specified for 32-point compact modules with two-wire connections. The total number of connection points does not represent independent I/O channels: supply and common-potential connections also form part of the layout. When selecting ET 200 connection modules, distinguish between channel count and terminal count.
Siemens specifies base dimensions of 120 × 132 × 43 mm (width × height × depth). Allow separately for the fitted compact module and cable routing when planning the enclosure layout.
Which IM151-1 COMPACT modules use this base?
6ES7151-1CA00-1BL0 — IM151-1 COMPACT 32DI: This version has 32 integrated digital inputs. When comparing ET 200 digital input solutions, distinguish this compact arrangement from stations assembled using separate input modules.
6ES7151-1CA00-3BL0 — IM151-1 COMPACT 16DI/16DO: This version has 16 integrated digital inputs and 16 digital outputs. In ET 200 digital output applications, using the same terminal base does not mean that wiring from the 32DI version can be retained unchanged. Check terminal assignments against the compact module actually fitted.
Difference between DL00 and DL10
6ES7193-4DL00-0AA0 / TM-C120C uses spring-loaded terminals. 6ES7193-4DL10-0AA0 / TM-C120S is the screw-terminal option. When ordering a spare, specify the connection type and full order number rather than simply requesting an “ET 200S COMPACT base”. Consult the terminal installation instructions for conductor size, stripping length and end preparation.
Supply wiring, potential groups and station structure
Review ET 200 power supply components separately from signal connections. For power distribution and potential groups, compare supply terminals, common references and I/O terminals with the existing wiring diagram. If additional potential connections are required, verify that any selected ET 200 additional modules and accessories are suitable for this base.
Within the ET 200 system architecture, the TM-C120C is the compact unit's wiring base. It should not be confused with PROFIBUS and PROFINET interfaces: the IM151-1 COMPACT models listed here communicate over PROFIBUS DP, while the terminal base provides no independent communication function.
Five checks before ordering
1. Exact model: Verify 6ES7193-4DL00-0AA0 and the TM-C120C designation on the base label.
2. Compact module: Identify the fitted unit by its full order number and confirm whether it is the 32DI or 16DI/16DO version.
3. Wiring record: Photograph terminal numbers and cable labels before removal. Check the new installation against the wiring diagram for the specific compact module.
4. Mechanical condition: Inspect spring terminals, contacts, housing and mounting parts. Investigate loose connections, damage or signs of overheating.
5. Scope of supply: Have the terminal base and IM151-1 COMPACT electronic unit listed separately in the quotation. Do not assume that all components shown in a photograph are included.
Editor's note: The important decision goes beyond spring versus screw terminals. Because the same base supports compact modules with different I/O arrangements, retaining the old wire positions does not by itself guarantee correct wiring. Keep the terminal base number, compact module number and cable list together in the maintenance record. Those three items provide the clearest basis for selecting a replacement.
Manuals and PDF documents
For model-specific terminal assignments and wiring drawings, visit the Siemens ET 200 PDF and user manuals page. The main reference is IM151-1 COMPACT Modules — A5E01077635-01. Use the 32DI or 16DI/16DO section that matches the compact module installed.
Related topics
Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules
Explore the station: About ET 200 · Communication interfaces · ET 200 manuals
Otomasyon AVM | Siemens:
Siemens main menu |
Siemens S7 PLC |
SIMATIC S7 |
ET 200 modules