6ES7 151-7AA10-0AB0

Siemens 6ES7151-7AA10-0AB0 – ET 200S IM151-7 CPU

Siemens 6ES7151-7AA10-0AB0 is the IM151-7 CPU with 48 KB of work memory for SIMATIC ET 200S. It executes a local control program and can connect to PROFIBUS as an intelligent slave. Within the Siemens ET 200 family, this is a standard automation CPU; it is not an F-CPU.

Memory, power supply and dimensions

The 48 KB work memory is non-expandable. A SIMATIC Micro Memory Card (MMC) provides load memory, and operation is battery-free. The supply is 24 V DC, with a permissible range of 20.4–28.8 V DC. Housing dimensions are 60 × 119.5 × 75 mm, stated as width, height and depth.

When reviewing a project, assess work-memory requirements separately from MMC capacity. Preparing a replacement CPU requires more than the presence of a memory card: check the card contents, hardware configuration and available project backup together.

MPI and PROFIBUS DP connections

The integrated 9-pin female Sub-D connector provides MPI/PROFIBUS DP communication. As an intelligent DP slave, the CPU executes its own program while exchanging configured data with a higher-level controller. Stand-alone operation can use MPI for programming and communication. There is no integrated PROFINET/Ethernet port.

PROFIBUS DP master functionality requires the 6ES7138-4HA00-0AB0 DP master module. The integrated slave connection and the additional master connection are separate interfaces. For system architectures, see ET 200 PROFIBUS and PROFINET.

STEP 7 and firmware compatibility

Engineering software must be selected together with the installed CPU firmware. In Siemens’ firmware compatibility table, the V2.1.9 entry for 6ES7151-7AA10-0AB0 specifies STEP 7 V5.2 SP1 with a hardware update. This does not mean that every AA10 CPU has V2.1.9 installed; read the actual version from the device.

Siemens product information states that the older hardware generation, including AA10, cannot be upgraded to the V2.6 firmware of the newer IM151-7 CPUs. Features belonging to AA20 and later models cannot be added to AA10 merely by loading firmware. Select update files using the complete order number and the manufacturer’s applicability information.

Station and module compatibility

When checking the station, compare the complete electronic-module order numbers, terminal modules, power groups and module sequence in HW Config. Membership of the ET 200 family alone does not establish compatibility with this ET 200S CPU. Different ET 200 subfamilies and IM151-7 F-CPU models must not be assumed interchangeable.

Before replacing the CPU, record the existing program, communication addresses and master-side data mapping. Selecting another IM151-7 model with more memory does not automatically establish project compatibility; check the configuration and operating behaviour with the replacement hardware.

Commissioning and fault diagnosis

When investigating communication problems, check the MPI/PROFIBUS address, transmission rate, cables and connectors, segment termination and master configuration. Evaluate the SF/BF indicators together with the STEP 7 diagnostic buffer. A BF indication alone does not prove that the CPU is defective; connection or configuration faults can also require investigation.

PDF documentation and user manuals

For documentation references, visit the Siemens ET 200 user manuals and PDF documentation page. Select a manual revision covering 6ES7151-7AA10-0AB0, and review the IM151-7 CPU manual, applicable product information and installed-module documentation together.

Related topics

Input and output modules: Digital input modules, digital output modules, analog input modules, special input modules and special output modules.

Power and connections: Power supply modules, power distribution modules, terminal blocks and connection modules.

Functions and expansion: Functional and safety modules, counter modules, positioning modules, additional modules and other network interface modules.

Safety systems and general information: ET 200 safety modules, ET 200 PROFIsafe and About Siemens ET 200.

These sections describe the wider ET 200 family. Links to safety topics do not imply that this standard CPU is an F-CPU or that it supports every F-module.

Navigation: Siemens Automation | Siemens S7 PLC | SIMATIC S7 | SIMATIC ET 200