6GK1 901-1BB20-2AB0
6GK1 901-1BB20-2AB0 — Siemens IE FC RJ45 Plug 90
Series: Siemens SIMATIC NET / Industrial Ethernet FastConnect. Category: Industrial network connection components.
6GK1 901-1BB20-2AB0 is a metal-housed RJ45 connector with a 90° cable outlet. It terminates four-core IE FC TP 2×2 cable in the field for 10/100 Mbit/s Industrial Ethernet. Applications include cabling between ET 200 stations, PLCs and network devices equipped with suitable RJ45 ports.
Package quantity and order numbers
The 2AB0 suffix identifies Siemens’ pack of 10 connectors. The same 90° connector is supplied individually under 6GK1 901-1BB20-2AA0 and in packs of 50 under 6GK1 901-1BB20-2AE0. These three order numbers distinguish package quantity, not transmission speed. For individual or used items, confirm the actual quantity being supplied.
Cable and port compatibility
FastConnect uses insulation displacement contacts for four conductors. The data sheet specifies AWG22 / 0.33 mm² conductors and a 6.5 mm cable diameter. Select an FC cable type approved by Siemens for this connector; the outside diameter alone does not establish compatibility with an ordinary patch cable.
This 2×2 version supports four-core 10/100 Mbit/s links; it is not an eight-core Gigabit connector. Suitable FC cable and network design allow direct device connections of up to 100 metres. Check the actual limit against the selected cable type and the complete link.
In the distinction between PROFIBUS and PROFINET, this component belongs to Ethernet/PROFINET cabling, not PROFIBUS DP. It does not replace a network interface, convert protocols or receive an IP address. Check the electrical suitability of the device port and the clearance between the 90° cable outlet, adjacent sockets and cabinet door.
Dimensions and environmental conditions
Connector dimensions are 13.7 × 16 × 42 mm, stated as width, height and depth. The product data sheet specifies an operating temperature of −40…+85 °C and an IP20 protection rating. These ratings do not extend the limits of the cable or connected equipment, and the assembly is not a water-protected field connector.
Assembly and retermination
Prepare the cable end to the dimensions in the Plug 90 assembly instructions. Follow the color markings on the contact covers. Seat the cable screen against the shield contacts and the outer jacket in the strain relief. Avoid damaging the latch spring when closing the housing, and engage the lock fully. Cable preparation must be carried out with the cable de-energized.
Siemens permits the insulation displacement contacts to be opened and reterminated up to 10 times. This is not the RJ45 plug’s mating-cycle rating. Cut off the previously pierced conductor section and prepare a fresh cable end. Where the device has no securing collar, provide cable strain relief close to the device.
Editor’s note: A sound-looking metal housing is only part of the inspection. Check the latch spring, contact covers and cable retention. A lit LINK indicator does not by itself confirm correct shielding or mechanical support. When investigating intermittent communication, inspect the cable termination too; reconnecting over an old contact mark can conceal the underlying problem.
PDF documentation and assembly instructions
Use the product data sheet together with the IE FC RJ45 Plug 90 assembly instructions, which also include a Turkish section. Visit the Siemens ET 200 PDF and user manuals page for documentation.
Related topics
Within an ET 200 system, network connections, terminal blocks and additional accessories perform different jobs. The power supply and power distribution must follow the station’s own wiring plan.
Digital inputs, digital outputs, function modules, counter modules and positioning modules belong to the station’s I/O system. This RJ45 connector adds no channels. Safety modules and PROFIsafe require suitable equipment and system configuration; connector selection alone does not provide those functions.
Navigation: Siemens automation > Siemens S7 PLC > SIMATIC S7 > Siemens ET 200