Siemens V20 fault index

Faults:
As soon as a fault occurs, the fault icon appears, and the display transitions to the fault screen. The fault screen displays the fault number preceded by "F."
Acknowledging/Clearing Faults:
+ To navigate through the current list of faults, press the or buttons.
+ To view the inverter status at the time of the fault, press the button for more than 2 seconds; to return to the fault code display, press the button for less than 2 seconds.
+ To clear/acknowledge the fault, press the button or acknowledge externally if the inverter has been set up accordingly; to ignore the fault, press the button.
After you acknowledge or ignore the fault, the screen returns to the previous display. The fault icon remains active until the fault is cleared/acknowledged.
Note:
The fault screen will display again under the following circumstances:
- If the fault has not been cleared and the button is pressed, the fault screen will display again.
- If there is no key press for 60 seconds.
** If a fault is active and there has been no key press for 60 seconds, the backlight (P0070) will flash.
+ When a fault occurs in an inverter, the fault icon lights up, signaling that there's an issue that needs attention. Here’s how you can navigate through the fault status:
Current Display: This is where you start when a fault is active. It's the default screen that shows the fault has occurred.
Fault Active: Once the fault is detected, you can press 'OK' to get more information. This will lead you to the fault code display.
Fault Code Display: Here, you’ll see the specific fault code related to the issue the inverter has encountered.
Viewing Inverter Status at Fault:
++ If you press and hold the 'OK' button for more than 2 seconds, the display will switch to the fault log menu. This menu will give you detailed parameters of the inverter at the time of the fault, like output voltage, output current, and the DC bus voltage.
++ If you briefly press the 'OK' or 'M' button (less than 2 seconds), you’ll return to the fault code display.
Fault Log Menu: A more detailed menu that provides an in-depth look at the inverter's status during the fault. It may include technical readings like output voltage (V), output current (A), Vdc (V), and frequency setpoint (Hz) after the RFG, often accompanied by a flashing red LED to indicate the fault condition.
After acknowledging or ignoring the fault, the screen will return to the previous display. However, the fault icon will stay lit until the fault is cleared or acknowledged properly.
Please Note:
- The fault screen will reappear if the fault hasn't been cleared and the button is pressed again.
- If there's no interaction (no key press) for 60 seconds, the fault screen will display again.
- If a fault is active and no key is pressed for 60 seconds, the backlight will flash as a reminder of the unresolved issue.
Fault Code index:
> F1: Overcurrent (details >>)
+ F2: Overvoltage (details >>)
+ F3: Undervoltage (details >>)
+ F4: Inverter overtemperature (details >>)
+ F5: Inverter I2t (details >>)
+ F6: Chip temperature rise exceeds critical levels (details >>)
+ F11: Motor overtemperature (details >>)
+ F12: Inverter temperature signal lost (details >>)
+ F20: DC ripple too high (details >>)
+ F35: Auto restart after n (details >>)
+ F41: Motor data identification failure (details >>)
+ F51: Parameter EEPROM fault (details >>)
+ F52: Inverter software fault (details >>)
+ F60: Asic timeout (details >>)
+ F61: MMC / SD card parameter cloning failed (details >>)
+ F62: Parameter cloning contents invalid (details >>)
+ F63: Parameter cloning contents incompatible (details >>)
+ F64: Inverter attempted to do an automatic clone during startup (details >>)
+ F71: USS setpoint fault (details >>)
+ F72: USS / MODBUS setpoint fault (details >>)
+ F80: AI lost input signal (details >>)
+ F85: External fault (details >>)
+ F100: Watchdog reset (details >>)
+ F101: Stack overflow (details >>)
+ F221: PID feedback below minimum value (details >>)
+ F222: PID feedback above maximum value (details >>)
+ F350: Configuration vector for the inverter failed (details >>)
+ F395: Acceptance test / confirmation pending (details >>)
+ F410: Cavitation protection failure (details >>)
+ F452: Belt failure (details >>)
Alarm Codes:
+ A501: Current limit (details >>)
+ A502: Overvoltage limit (details >>)
+ A503: Undervoltage limit (details >>)
+ A504: Inverter overtemperature (details >>)
+ A505: Inverter I2t (details >>)
+ A506: IGBT junction temperature rise warning (details >>)
+ A507: Inverter temperature signal lost (details >>)
+ A511: Motor overtemperature I2t (details >>)
+ A535: Braking resistor overload (details >>)
+ A541: Motor data identification active (details >>)
+ A600: RTOS overrun warning (details >>)
+ A910: Vdc_max controller deactivated (details >>)
+ A911: Vdc_max controller active (details >>)
+ A912: Vdc_min controller active (details >>)
+ A921: AO parameters not set properly (details >>)
+ A922: No load applied to inverter (details >>)
+ A923: Both JOG left and JOG right are requested (details >>)
+ A930: Cavitation protection warn (details >>)
+ A936: PID autotuning active (details >>)
+ A952: Belt failure detected (details >>)
+ V20 Error Index
+ V20 Error Codes 1
+ V20 Error Codes 2
+ V20 Error Codes 3
++ Siemens Homepage
"All the guides and error codes on this page have been created by members of our community. The information has been prepared as faithfully as possible to the original; however, the error codes and technical specifications of devices can be subject to interpretation. Official manufacturer guides should be considered the primary source. Do not hesitate to contact our community if you notice any inaccuracies or if you wish to contribute."