6ES5 262-8MA12
Siemens 6ES5 262-8MA12 SIMATIC S5 IP 262 closed-loop control module
The 6ES5 262-8MA12 is an IP 262 K-type PID control module for the S5-90U, S5-95U and S5-100U. It compares measured values with their setpoints and can drive three continuous control loops through three analog current outputs. Applications include temperature, pressure and flow control. In pump pressure control, an output can supply the drive’s current reference.
Inputs, outputs and wiring
Four analog inputs can accept setpoints and measured values. Depending on channel selection and wiring, the inputs accept 0–20 or 4–20 mA, J/K/L/S thermocouples, or Pt100 sensors. When connecting a current source such as a pressure transmitter, match the feedback scaling to the sensor’s measurement range. The module also provides four digital control inputs.
The three analog outputs are non-isolated. Each can be set to 0–20 or 4–20 mA, with a maximum total load of 600 Ω. The front 25-pin Sub-D handles the analog and digital inputs, and the 15-pin Sub-D is the PG/OP port. The outputs and external 24 V DC supply connect to the bus-unit terminal block. Check the S5 power supply, cable type and bus-unit terminal layout separately.
STEP 5 and ET 200U
For S5-90U, S5-95U and S5-100U installations, the Siemens IP 262 software package includes FB 61 and FB 62 for CPU data exchange. The IP 262 can also operate independently with a directly supplied setpoint and 24 V. When the CPU supplies the setpoint, the module configuration determines which setpoint it uses if the CPU fails.
In an ET 200U station, such as one fitted with an IM 318-B, the module uses 8 input bytes and 8 output bytes. COM ET 200 can assign different start addresses to these areas. Allow at least 200 ms between accesses to the module. Siemens provides FB 60 as an example for data exchange through ET 200U.
Siemens APPnote 249 on S5 function modules documents direct online access from STEP 5 for the 8MA12. It specifies the 6ES5 734-2BF00 cable for the PG 720/740. Online access requires 24 V DC across terminals 1 and 2 of the bus unit.
8MA12 and 8MB12 differences
The 8MA12 is the K-type module with three analog current outputs. The 6ES5 262-8MB12 is the S-type module with eight digital outputs for pulse or three-position step control. When selecting a spare, check the complete order number and the actuator’s command signal. Review the PID gains after verifying the measurement and output.
Editor’s note
1. For a used module, check the 8MA12 suffix on the label and ask for a load test on all three current outputs. Record the current range used for the test.
2. Before replacement, use STEP 5 to read back and save the module structure and parameters. Then isolate panel and field power. Photograph the input selector positions, connectors and terminals before removing the module.
3. If the programmer cannot see the module, check the bus unit’s 24 V supply first. If the supply is present, verify the cable specified for your programmer and the module’s 15-pin port.
4. If the process reading jumps, check the channel selector, sensor type and software scaling together. Compare the module’s reading with an independent measurement before tuning the PID loop.
5. If the command changes but the valve or drive does not respond, compare the output current with the receiving input range. Check the combined load of the receiver and any series devices against the 600 Ω limit.
6. After replacement, verify the manual-to-automatic transfer and the setpoint used on loss of CPU communication under safe test conditions. Record the result for each loop.
To sell a 6ES5 262-8MA12, send the quantity, working condition, label photo and asking price to otomasyonavm@gmail.com.
Manuals and reference documents
+ Siemens 6ES5 262-8MA12 data sheet (EN)
+ Siemens IP 262 module manual, 09/2001 (DE)
+ Siemens S5-100U system manual, section 15.7 (EN)
+ Siemens ET 200U manual, section 9.7 (EN)
+ Siemens APPnote 249, STEP 5 connection (EN)
+ Siemens ST 50, IP 262 specifications (EN)