6ES5 305-7LA11

Siemens 6ES5 305-7LA11 — IM 305 Interface Set with 0.5 m Cable

Siemens 6ES5 305-7LA11 is an IM 305 interface set connecting one expansion unit to a central controller in a SIMATIC S5-115U system. It comprises two modules permanently joined by a 0.5 m cable. This member of the S5 interface module family is used for centralized expansion with fixed slot addressing.

Siemens specifies a maximum of 1 A supplied to the expansion unit and 10 mA own consumption from the 5 V supply. Total set weight is approximately 0.6 kg. The 1 A supply capacity and 10 mA own consumption are different ratings. Include the load of all installed modules when assessing the power supply.

0.5 m cable and set completeness

The connecting cable permanently joins the two modules. For a used item, check that both modules and the connecting cable are present. The manufacturer’s set description does not by itself establish the completeness of a particular sale. Confirm the actual scope of delivery against photographs and part information.

The Siemens S5-115U manual states that the 0.5 m cable is too short to position the expansion unit below the central controller. A different arrangement may require the 1.5 m cable version, 6ES5 305-7LB11, or an appropriate IM 306 configuration. Do not change the layout by adding an improvised cable extension.

Rack arrangement and fixed slot addressing

Record the complete rack numbers on both sides of the connection. Check module types and slot positions in expansion racks such as ER 701-1LA11 and ER 701-1LA12. Identify the installed central rack as well, for example CR 700-0LB11, CR 700-2LA12 or CR 700-3LA12.

IM 305 supports fixed slot addressing only. Assess addresses for digital input, digital output and suitable analog modules against their slot positions and the CPU system’s address table. Before moving a module, check the addresses used in the STEP 5 program and the system’s restrictions on analog module placement.

Distinction from IM 306

6ES5 306-7LA11 — IM 306 is a separate expansion solution. The S5-115U manual compares one expansion unit and fixed addressing for IM 305 with up to three expansion units and variable slot addressing for IM 306. Assess cabling, supply and address assignments together before changing the interface arrangement.

Troubleshooting and used-part assessment

During PLC troubleshooting, check the supply, seating of both interface modules, fixed cable and connectors in sequence. Inspect grounding connections and nearby sources of electromagnetic interference. If several modules in the same expansion rack become inaccessible, investigate their common connection path.

Editor’s note

Start by asking whether both ends are included. On an older Siemens S5 system, a photograph of one board may be used to describe an entire set. Seeing both modules and the complete cable together avoids a great deal of confusion when ordering.

Measure the rack arrangement before assuming that half a metre will reach. Choosing the correct cable-length version is much easier than trying to force a short fixed cable into an unsuitable route.

Remember that IM 305 uses fixed slot addressing. Check the address table before moving a serviceable I/O module to another slot for a test. A small physical change can alter the input and output arrangement expected by the program.

Back up the program and record the RAM/EPROM memory arrangement, module sequence and cable routing before removal. Isolate the supply and verify that the equipment is de-energized. Do not pull on the fixed cable to extract either module.

Inspect the cable entries and connectors on a used set. Ask about crushing, sharp bends, corrosion or later splices. Find out which central controller and expansion rack were used for testing; a clean appearance is not a substitute for an operating test.

OtomasyonAVM resources and PDFs

+ OtomasyonAVM S5 PDF archive

+ S5 interface modules · S5 mounting racks

Related topics

+ 6ES5 305-7LB11 — IM 305 with 1.5 m cable

+ 6ES5 306-7LA11 — different addressing and expansion arrangement

+ 6ES5 701-1LA11 — ER 701-1 expansion rack

+ 6ES5 700-2LA12 — CR 700-2 central rack

Browse SIMATIC S5

+ S5 interface modules

+ S5 cables and connectors

+ S5 mounting racks

+ SIMATIC S5 overview

+ Used Siemens equipment

Siemens and external references

+ Siemens S5-115U manual — English; pp. 3-18/3-19: centralized expansion and fixed addressing; p. 15-60: exact-code IM 305 specifications

+ Siemens ST 50, 1998 — English; pp. 3/82–3/83: IM 305 application, 0.5 m LA11 and 1.5 m LB11 order numbers; archived copy