6ES5 900-7AB21
Siemens 6ES5 900-7AB21 – S5-110A CPU 900 central processing unit
Siemens 6ES5 900-7AB21 is a CPU 900 central processing unit for the S5-110A. This SIMATIC S5 unit executes the machine’s control program. Maintenance of a Siemens S5 installation should cover its program memory, connection arrangement and existing peripheral modules together.
6ES5 900-7AB11, 6ES5 900-7AC21 and 6ES5 900-7AD11 are different order codes within the CPU 900 group. Check the complete suffix and hardware revision before replacement; similar appearance does not establish interchangeability.
Program memory and backup
The S5-110A family uses a plug-in 910 EPROM memory submodule for its program. Record the complete code and contents of the installed S5 memory module. The CPU label alone does not identify the supplied program capacity or establish that the machine program is included.
For PLC programming, preserve the existing program and the programming software used with it. Follow the S5-110A instruction set; verify DB, function-block and arithmetic requirements rather than transferring specifications from later S5 processors.
Programmer connection and test equipment
The Siemens family manual describes the 500 programmer interface for PG 630, PG 631 and PG 670, using a parallel connection. Match the programming cable and interface hardware to the existing installation. Do not assume that a standard S5 TTY cable alone provides access.
The family’s 330 test module displays program statements, signal states and the result of logic operation (RLO). Before PLC troubleshooting, verify the test equipment, connecting cable and memory arrangement against the installed CPU revision.
Inputs, outputs and addressing
Record the complete codes of the digital input and digital output modules. Select field voltage and load current for the actual peripheral module. The CPU 900 code does not establish sensor PNP/NPN characteristics or the switched output voltage.
Compare the printed slot addresses on the S5 mounting rail with the program. Modules listed in the S5-90/110 group require individual system checks. Photograph the slot sequence, links and connections before replacement and retain the existing address plan.
Power supply and peripheral connections
The S5-110A family arrangement uses a 930 power supply for internal 5 V DC. Check the complete S5 power-supply code. Use the system wiring diagram for measurements and connections; never apply mains or 24 V field power directly to CPU connections.
Identify the functions of any communications modules separately. An external interface does not establish built-in CPU RS232, RS485, Ethernet or PROFIBUS ports. Record both cable ends and the connected device.
Used-unit and replacement checks
For a used PLC CPU, establish the 6ES5 900-7AB21 label, board revision, fitted EPROM and delivery scope. When buying used Siemens equipment, distinguish hardware supplied with a recoverable application from a blank or undocumented module.
Base model comparisons on the CPU, memory and peripheral modules together. If considering Derell PLC options for modernization, redesign the existing I/O, control sequence and timing for the new project; the original EPROM is not directly transferable to a modern PLC.
Editor's Note
Start with the 7AB21 label and fitted EPROM together. A CPU 900 supplied as hardware does not necessarily include the program required by your machine.
Record the working program-reading method. Photograph the EPROM orientation, label and socket position before removal. Obtain a dependable backup before attempting erasure or programming.
If programmer access fails, inspect the 500 interface, cable and programmer together before condemning the CPU. A cable working on another S5 installation may serve a different connection arrangement.
Where an old backup battery is fitted, inspect for leakage, corrosion and damaged surrounding tracks. Resolve supply faults before evaluating a replacement processor.
A bench check should establish program execution and the expected output response to a sample input. Record which memory and peripheral modules were used to obtain the result.
OtomasyonAVM resources and PDFs
6ES5 900-7AB21 main page · Used Siemens S5 models · Siemens S5 PDF archive
Document scope: The Siemens S5-110A family manual below supports the system memory and connection arrangement. Its CPU specification tables explicitly name 6ES5 900-7AD11. Exact 7AB21 memory capacity, retentive-flag count, execution time and current were not verified and are therefore omitted. This document is not presented as a dedicated 7AB21 technical sheet.
Related topics
6ES5 900-7AB11 · 6ES5 900-7AC21 · 6ES5 900-7AD11 · 6ES5 500-7AA11 PG interface · Derell PLC options
Navigation
SIMATIC S5 · Siemens S5 models · Used Siemens · S5 memory modules · S5-110A test module
Siemens and external references
Siemens S5-110A Operating Instructions – system arrangement, English
500 programmer interface · 330 test module and 332 test adapter · CPU specification table explicitly limited to 7AD11