6ES5 686-4AA11
6ES5 686-4AA11 – SIMATIC S5 External 5.25-Inch Floppy Disk Drive
Siemens 6ES5 686-4AA11 is identified in archived parts records as an external 5.25-inch floppy disk drive for SIMATIC S5 service equipment. It is a peripheral considered for accessing legacy program and data diskettes. 5.25 inches describes the physical media size; it does not establish recording capacity, file format or compatibility with a particular programmer.
Assess the drive together with its connection accessories, host programmer and diskette archive. For someone recovering a machine project, the objective is more than getting the disk to rotate: files must be read correctly and copied into a usable backup. The only original project diskette should not be the first test medium.
Media size, capacity and file format
When comparing data-storage media, distinguish physical size from storage capacity. For 6ES5 686-4AA11, capacity, recording density and supported formats require exact documentation or a verified device test. The 5.25-inch designation alone does not justify a specific KB/MB rating or support for every legacy diskette.
A readable directory does not prove that every file is intact. During archive transfer, read files completely, verify the copies and record any files that cannot be recovered. If the operating system does not recognise a diskette, formatting the original is not a recovery method; establish its media and file format first.
Host programmer, connection and power checks
A service inventory may contain different programmers, such as a PG 635 or PG 685. Their presence in the same S5 family does not establish direct compatibility with this drive. Verify the host's complete model, hardware revision, operating system and external-drive connection together.
When assessing S5 cables and connection sets and interface hardware, a connector that physically fits is insufficient evidence. Check cable function, orientation and the drive's power label. Until exact installation documentation is available, do not assume a pin assignment, supply voltage or direct USB/serial connection.
Software archives versus drive hardware
S5-DOS basic packages, STEP 5 PC software packages and specialised software such as COM PMC must be assessed for their individual versions and operating environments. Physically reading a diskette does not establish that its software will run on the current computer or that the required licence is available. Preserve comments, symbols and associated project files alongside the program files.
The drive's function also differs from that of EPROM memory, S5 memory cards and an EPROM programmer. Reading a file from diskette does not automatically write it to a memory module or download it to a PLC. Plan the next transfer stage for the actual programming environment and target device.
Assessing read and write tests
Start with a known good, correctly formatted test diskette whose contents can be replaced. If write operation has been verified for the intended setup, write a file to a separate test diskette, read it back and compare its contents. Record read and write tests as separate results.
For storage reliability, one successful attempt is insufficient. Repeated read errors require investigation of both the drive and the medium. To reduce data loss, do not remove a diskette during access, and keep the original archive separate from testing and write operations.
Editor’s Note
When purchasing used Siemens equipment, ask for photographs of the label, rear connections, cable and any associated power equipment. A clean front panel tells only part of the story; an incomplete connection set can take more effort to resolve than the drive itself.
Do not put the machine's only project diskette into this S5 peripheral for its first test. Establish operation with a test diskette and protect the original archive. Testing an old drive should not create a new data-recovery problem.
During S5 maintenance, mechanical behaviour matters. Stop if the diskette jams, rubs or the drive makes unusual noises. Avoid adjusting heads or mechanisms by trial and error; first establish the correct medium, connection and condition of the drive.
When recovering an archive for a SIMATIC S5 system, retain more than a screenshot of the directory. Copy files completely, distinguish recovered files from unreadable ones and photograph the original diskette labels. Check separately that the resulting copies can actually be opened.
For S5 service equipment, record the host PG, operating system, cable, diskette format and separate read/write results. An activity light alone is insufficient; the useful result is knowing what the drive could read in a documented setup.
OtomasyonAVM resources and PDFs
Browse S5 accessories for service equipment, S5 cables and connectors for connections and the S5-DOS basic package page for software context.
+ Shared SIMATIC S5 PDF and system manual archive. The Siemens PG manual below provides general diskette-handling guidance; it is not an installation manual for 6ES5 686-4AA11.
Related topics
+ Causes of data loss and storage-media reliability.
+ S5 memory cards and EPROM programming equipment.
Browse SIMATIC S5
S5 accessories · S5 cables · SIMATIC S5 systems · Siemens S5 PLCs · Siemens second-hand equipment
Siemens and external references
Siemens PG 750-486 Programmer Manual (English PDF). Section 3.2.1 and the fault table cover general diskette handling and write protection. Specifications for that PG's internal drives have not been assigned to the 686-4AA11.
ADEGIS archived SIMATIC S5 parts list, p. 24: exact order-number entry for an external 5.25-inch floppy disk drive. This record does not replace manufacturer installation documentation.