6ES5 434-7LA12
Siemens 6ES5 434-7LA12 – 8-Channel 24 V DC Process Interrupt Input Module
6ES5 434-7LA12 is an 8-channel, 24 V DC digital input module with programmable process interrupts for S5-115U in the Siemens SIMATIC S5 family. Each channel on this S5 input module is individually isolated by an optocoupler (8 × 1). With appropriate programming, a rising or falling edge at a selected input can request a CPU interrupt.
In a SIMATIC S5 installation, it supports position signals, event detection and responses to specific signal changes. It can also read 24 V DC signals switched by contactor auxiliary contacts and relay contacts. Check the S5 system architecture, CPU, rack and program together; fitting the module alone does not configure interrupt processing.
Input voltage, current and response time
Rated input voltage is 24 V DC. The specified ranges are −30 to +5 V for logic 0 and +13 to +30 V for logic 1. The +5 to +13 V region must not be used as a defined logic state. Typical input current at 24 V DC is 8.5 mA.
Response time is 0.5–1.5 ms for both 0→1 and 1→0 transitions. This is the module's input response, while the complete machine response also includes CPU interrupt response and execution of the interrupt program.
The manufacturer permits 2-wire BERO proximity switches with a maximum quiescent current of 1.5 mA. For a relay contact or sensor output, check off-state leakage as well as the active signal voltage.
Initializing process interrupts
Configure the interrupt-enabled inputs and the triggering edge for each input in restart blocks OB21 and OB22. The CPU project and PLC program must transfer this initialization data to the module.
The first output byte carries the interrupt-enable mask; the second carries the edge-selection mask. These addresses write module parameters and do not represent physical digital output channels on the board.
Addressing and direct peripheral access
Although the module has eight physical inputs, it occupies two input bytes and two output bytes. In the S5-115U's IM 306 slot-addressing arrangement, select 16 channels. Allow for this address requirement when checking the S5 rack and slot arrangement.
On the input side, the base address gives the current input states, while base address +1 identifies interrupt-initiating channels. With a base address of 8 (08h), status is at byte 8 and the interrupt register is at byte 9. Input status is not transferred automatically to the process input image; use direct peripheral access.
Reading the interrupt byte automatically clears its register on the module. Store and evaluate the value from the first read instead of repeatedly reading the byte to identify the same event. During troubleshooting, distinguish present input states from the interrupt record.
MELD indication and RESET
A process interrupt lights the yellow LED and closes the latching relay contact at the MELD terminals. This external indication retains its state through a power failure. Reset it through the 24 V DC RESET input. Reading the interrupt byte and resetting the retained external indication are separate operations.
Supply and field connections
Current drawn from the internal 5 V supply is less than 70 mA. Typical power loss is 2 W, and weight is approximately 0.7 kg. In power supply and PLC supply calculations, assess internal board consumption separately from the external 24 V field circuits.
Maximum cable length is 600 m unshielded or 1000 m shielded. Follow each input's own signal/M pair when checking S5 connection parts and the front connector. Inspect electromagnetic interference, earthing and field-circuit fuse protection. External common reference connections affect channel independence in the installed circuit.
Related order numbers and used-module checks
6ES5 434-7LA11 is a related order number; compare version and interrupt-function details. 6ES5 430-7LA12 is a 32-channel 24 V DC input module, while 6ES5 431-7LA11 is a 16-channel 24/48 V UC model. 6ES5 434-4UA12 is a 32-channel 5–15 V DC input module. A shared 434 designation does not establish electrical or functional equivalence.
For used Siemens equipment, test interrupt generation, retained MELD indication and RESET alongside all eight inputs. Assess the label and front connector together with a backup of the existing program.
Editor’s note
Do not finish the test when all eight input LEDs light up. The interrupt function is what makes this module different. Check that the correct edge generates an interrupt and that the program handles the event.
When allocating addresses, eight inputs do not mean one byte here. The module uses two input and two output bytes; check the IM 306's 16-channel setting as well. An incorrect address arrangement can make a sound board appear faulty.
Take care not to lose the interrupt record while investigating it. Store the value from the first read; a second read may no longer contain the previous event. Check whether another program block is reading that same byte.
A lit yellow LED or active MELD contact does not by itself prove a board fault. This indication can remain after power is removed. Check CPU interrupt acknowledgement and external RESET separately; cycling power does not clear everything.
Before fitting a spare, back up the program and photograph the address arrangement and front connections. Check supply and sensor signals first, then initialization and interrupt processing. Isolate power before working; those records make replacement much easier.
OtomasyonAVM resources and PDFs
Start with the OtomasyonAVM Siemens S5 PDF archive, About Siemens S5 and S5 digital input modules.
Electrical specifications appear on printed page 15-24 of Siemens S5-115U, 6ES5 998-0UF23 / EWA 4NEB 811 6130-02b. Process interrupts, initialization and addressing are described in section 9.3, pages 9-5 to 9-7. In the PDF below, these correspond to pages 552 and 285–287.
Related topics
+ 6ES5 434-7LA11 · 6ES5 430-7LA12 · 6ES5 431-7LA11 · 6ES5 434-4UA12.
+ PLC programming · PLC troubleshooting · Connectors.
Browse SIMATIC S5
Siemens S5 home · S5 digital input modules · S5 PDF archive · Used Siemens equipment
Siemens and external references
+ Siemens S5-115U system manual – English PDF: 6ES5 434-7LA12 specifications, terminal arrangement and 434-7 process-interrupt operation.