Siemens G120 fault codes 2
F01000 - Internal Firmware Error
> Meaning: A problem has been detected in the inverter's internal firmware.
- Cause: Firmware error or corruption.
+ Solution: Replace the inverter.
F01001 - Floating Point Exception
> Meaning: An error occurred during floating point operations in the inverter.
- Cause: Unexpected situation in mathematical operations.
+ Solution: Turn off and restart the inverter.
F01015 - Internal Firmware Error
> Meaning: A problem has been detected in the inverter's internal firmware.
- Cause: Firmware error or corruption.
+ Solution: Update the firmware or contact technical support.
F01018 - Power On Cancelled Multiple Times
> Meaning: The inverter has failed to perform the power-on process multiple times.
- Cause: The inverter cannot start properly due to an electrical or hardware issue.
+ Solution:
++ Turn off and restart the inverter's power supply.
++ After this error, the inverter will power on with factory settings.
++ Re-commission the inverter.
A01028 - Configuration Error
> Meaning: Parameter assignments on the memory card were made with an incompatible module type.
- Cause: Parameter settings for a different module type are not compatible with the current module.
+ Solution: Check module parameters and re-commission if necessary.
F01033 - Unit Change: Reference Parameter Value Invalid
> Meaning: The value of the reference parameter is invalid.
- Cause: The reference parameter value may have been set to 0.0.
+ Solution: Set the reference parameter value to something other than 0.0 (p0304, p0305, p0310, p0596, p2000, p2001, p2002, p2003, r2004).
F01034 - Unit Change: Failed Calculation of Parameter Values After Reference Value Change
> Meaning: The calculation of parameter values failed after a change in the reference value.
- Cause: The reference parameter value may have been set in a way that it cannot be calculated in the unit notation of the relevant parameters.
+ Solution: Choose an appropriate value for the reference parameter value so that it can be calculated in the unit notation of the relevant parameters (p0304, p0305, p0310, p0596, p2000, p2001, p2002, p2003, r2004).
F01040 - Parameters Must Be Saved
> Meaning: The parameters need to be backed up.
- Cause: The parameters need to be backed up to prevent loss.
+ Solution: Back up the parameters (p0971). Turn off and restart the inverter.
F01044 - Memory Data Card Loading Error
> Meaning: An error occurred while loading the memory card.
- Cause: The memory card may be faulty or the inverter card may not be able to read it.
+ Solution: Replace the memory card or the inverter.
F01105 - CU: Insufficient Memory
> Meaning: There is not enough memory in the control unit.
- Cause: Too many data sets may be in use.
+ Solution: Reduce the number of data sets.
F01122 - Probe Input Frequency Too High
> Meaning: The frequency value at the probe input is too high.
- Cause: Signals with too high frequency may be sent to the probe input.
+ Solution: Reduce the frequency of pulses at the probe input.
F01205 - CU: Time Slice Overflow
> Meaning: A time slice overflow occurred in the control unit.
- Cause: Timing issues may arise due to processor load.
+ Solution: Contact technical support.
F01250 - CU Hardware Error
> Meaning: A hardware error has been detected in the control unit.
- Cause: A hardware malfunction in the control unit.
+ Solution: Replace the inverter.
F01512 - Failed Attempt to Create Conversion Factor for Scaling
> Meaning: The conversion factor required for scaling could not be created.
- Cause: A specific scaling factor may not have been defined.
+ Solution: Create scaling or check the transfer value.
A01590 - Motor Maintenance Interval Expired
> Meaning: The maintenance time for the motor has expired.
- Cause: The motor needs maintenance after a certain period of operation.
+ Solution: Perform maintenance on the motor.
Reminder: Siemens G120 and other Siemens drive are available for sale at Otomasyon Mall. Please note that some devices are used products, so take this into consideration when purchasing. Once these products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. (04.09.2011)
Please Note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please feel free to share them with us!