Omron V7 fault codes 4

UL3 (Insufficient Torque Detection): When V/f mode is selected, the inverter output current was below the Insufficient Torque Detection Level (n118). When vector mode is selected, the output current or output torque was below the detection level (n097 to n118).

   Check: Check the n118 setting, verify operating conditions, and correct the cause of the fault.

EF (External Fault): The inverter received an external fault input from the control circuit terminal.

   Check: Check the NO/NC contact selection, wiring, and ensure no signal is received from the PLC.

CPF-00: The inverter failed to communicate with the Digital Operator for 5 seconds or longer when the power was turned on.

   Check: Verify that the Digital Operator is securely mounted, then turn the power off and on again. If the fault persists, replace the Digital Operator or the inverter.

CPF-01: A transmission error occurred with the Digital Operator for 5 seconds or longer when transmission started.

   Check: Verify that the Digital Operator is securely mounted, then turn the power off and on again. If the fault persists, replace the Digital Operator or the inverter.

CPF-04: An EEPROM error was detected in the inverter control circuit.

   Check: Save all constant data and initialize the constants. Turn the power off and on again. If the fault persists, replace the inverter.

CPF-05: An AD converter error was detected.

   Check: Turn the power off and on again. If the fault persists, replace the inverter.

CPF-06: An option card connection error or an inappropriate option card was detected.

   Check: Verify the connection of the communication option card, then turn the inverter power off and on again. Confirm the Software Version Number (n179). Check the appropriate inverter software number listed in the Communication Option Card instruction manual.

CPF-07: An operator control circuit (EEPROM or AD converter) error was detected.

   Check: Verify that the Digital Operator is securely mounted, then turn the power off and on again. If the fault persists, replace the Digital Operator or the inverter.

CPF-11: Combination error. The control circuit is not combined with the correct software. (Contact your OMRON representative.)

Communication Option Card Self-Diagnostic Error: Option card error. Replace the option card. Ensure there are no foreign substances in the Communication Option Card.

Communication Option Card Model Code Error, Communication Option Card DPRAM Error

OPR (Operator Connection Error): Turn the power off and on again. If the fault persists, replace the inverter.

CE (MEMOBUS Communication Error):

   Check: Communication devices or signals, ensure the PLC is not faulty, verify the transmission cable is correctly connected, check for loose terminal screws, and ensure wiring is done correctly.

STP (Emergency Stop): The inverter stopped according to constant n005 after receiving an emergency stop error signal.

   Check: NO/NC contact selection, ensure wiring is done correctly, and check that no signal is received from the PLC.

FBL (PID Feedback Loss Detection): The PID feedback value fell below the detection level. When PID feedback loss is detected, the inverter operates according to constant n136.

   Check: Inspect the mechanical system and correct the cause, or increase the value of n137.

Communication Option Card Error: A communication error occurred while the communication option card was in use and when a Run Command or frequency reference was entered from the PLC.

   Check: Communication devices or signals, ensure the PLC is not faulty, verify the transmission cable is correctly connected, ensure wiring is done correctly, check for loose terminal screws, and ensure the communication option card is correctly installed.

Protective Action:

   Check: Power supply voltage, main circuit power supply connections, terminal screws (loose?), control sequence, and replace the inverter if necessary.

Errors Occurring During Auto-Tuning:

   E02 Alarm: An alarm (XXX) was detected during tuning.
   Check: Input data, check wiring and machine environment, verify load.
   E03 STOP Button Input: The STOP button was pressed during tuning, and tuning was canceled.
   E04 Resistance Error: Tuning did not complete within the specified time, or the tuning results were out of the constant setting range.
   Check: Verify input data, check motor wiring, disconnect the motor from the machine system during rotary tuning, change Maximum Voltage if it is higher than the inverter input power supply voltage.
   E05 No Load Current Error
   E09 Acceleration Error: The motor did not accelerate within the specified time.
   Check: Increase Acceleration Time 1 (n019), return Stall Prevention Level During Acceleration (n093) to its initial value if it was lowered, disconnect the motor from the machine system if connected.
   E12 Current Detection Error: The current flow exceeded the motor rated current, the polarity of the detected current was reversed, or one of the U, V, and W phases was open.
   Check: Inspect the current detection circuit, motor wiring, and current detector installation.

The motor does not run when an external operation signal is input:

   Check: Incorrect operation method selection, the Run command (n003) is not set to the Control Circuit Terminal, Multi-function Input Selection (n052) is set to 3-wire sequence and the S2 control terminal is not closed, the frequency reference is too low, Local mode is enabled, V-I SW (SW2) setting is incorrect, NPN/PNP switch (SW1) setting is incorrect, Program mode is enabled.

The motor stops. No torque output:

   Check: Stall prevention level is too low during acceleration, stall prevention level is too low during operation, the load is too heavy, when Maximum Frequency (n011) is changed, the maximum voltage frequency (n013) is also changed, V/f set value is too low for low-speed operation, analog reference input is unstable, and there is noise interference.

The Digital Operator's LED does not light:

   Check: No power, Digital Operator is not mounted correctly, short-circuit bar for +1 and +2 terminals is not connected, POWER charge indicator lamp lights after power is turned on but Digital Operator gives no display, main circuit fuse blew, replace the inverter.