Omron A1000 fault codes 8

oH
The message "Heatsink Overheat" is indicating that the temperature of the heatsink, which is a component used to dissipate heat from the drive, has exceeded the pre-set alarm level. The default value for the alarm level is determined by the drive's capacity.

There are several potential causes for this issue, including:

    Surrounding temperature is too high: It is necessary to check the temperature of the environment around the drive and verify that it falls within the drive's specifications. Improving air circulation within the enclosure, installing a fan or air conditioner to cool the area, or removing any sources of excessive heat near the drive may help resolve the issue.
    Load is too heavy: Measuring the output current and decreasing the load, or lowering the carrier frequency (C6-02), may help to resolve the issue.
    Internal cooling fan has stopped: Replacing the cooling fan may be necessary. Additionally, after replacing the drive, the cooling fan maintenance parameter (o4-03=0) must be reset.

It is important to address this issue as soon as possible, as overheating can cause permanent damage to the drive and affect its performance.


Solutions must be found based on the listed causes. First, the surrounding temperature must be checked to see if it exceeds the specified limits and air circulation must be improved or an air conditioning system used. Additionally, the load must be decreased or the cooling fan replaced. Finally, after replacing the drive, the cooling fan maintenance parameter must be reset to (o4-03=0).
--------------------
oH1 Overheat 1 (Heatsink Overheat)
The "oH1 AC Drive Overheat 1 (Heatsink Overheat)" message is indicating that the temperature of the heatsink, which is a component used to dissipate heat generated by the AC drive, has exceeded the pre-set overheat level. The overheat level is determined by the drive's capacity, which is set in the parameter o2-04.

There are three possible causes for this issue:

    Surrounding temperature is too high: The temperature surrounding the drive should be checked to ensure that it is not too high. This could be due to poor air circulation within the enclosure, high ambient temperature, or objects near the drive that are generating heat. To resolve the issue, improving air circulation within the enclosure, installing a fan or air conditioner to cool the area, or removing any sources of excessive heat near the drive may help.

    Load is too heavy: If the load on the drive is too heavy, it can cause the heatsink temperature to exceed the overheat level. To resolve the issue, the output current should be measured and if necessary, the load should be reduced and/or the carrier frequency (C6-02) should be lowered.

    Internal cooling fan has stopped: If the internal cooling fan has stopped, it could cause the heatsink temperature to rise and trigger the overheat message. To resolve the issue, the cooling fan should be replaced.

It is important to address this issue as soon as possible, as overheating can cause permanent damage to the drive and affect its performance.


oH3 Motor Overheat Alarm (PTC Input)
• The temperature of the motor has exceeded the alarm detection level as indicated by the signal to the analog input terminal A1, A2, or A3.
• Detection of this alarm requires that multi-function analog input H3-02, H3-06, or H3-10 be set to "E".
Cause Possible Solution
Motor has overheated.
• Check the size of the load, acceleration and deceleration times, and cycle times.
• Reduce the load.
• Increase acceleration and deceleration times (C1-01 to C1-08).
• Adjust the preset V/f pattern (E1-04 to E1-10), mainly by reducing E1-08 and E1-10.
• Be cautious not to reduce E1-08 and E1-10 too much as this reduces load tolerance at low speeds.
• Verify the motor rated current and enter it as indicated on the motor nameplate (E2-01).
• Ensure the motor cooling system is functioning properly.
• Repair or replace the motor cooling system if necessary.

oH4 Motor Overheat Fault (PTC Input)
• The motor has overheated, as indicated by the signal received by the analog input terminal A1, A2, or A3. This signal has exceeded the fault detection level set by the multi-function analog input H3-02, H3-06, or H3-10 = "E".

Possible Causes and Solutions:
• Check the size of the load, the acceleration and deceleration times, and the cycle times to determine if the load is too heavy. Reduce the load if necessary.
• Increase the acceleration and deceleration times (C1-01 through C1-08) to help the motor cool down.
• Adjust the preset V/f pattern (E1-04 through E1-10) by reducing E1-08 and E1-10, but be careful not to reduce them too much as this can reduce load tolerance at low speeds.
• Check the motor's rated current and enter it as indicated on the motor's nameplate (E2-01).
• Ensure that the motor cooling system is functioning properly and repair or replace it if necessary.

+  A1000 Fault index >

+ Next page >>

- previous page <<