Omron A1000 fault codes 10
ov Overvoltage
Overvoltage is a condition in which the voltage in the direct current (DC) bus exceeds the normal operating level. This can occur due to a variety of reasons such as electrical faults or malfunctions in the power supply. If the voltage exceeds the overvoltage detection level, it can result in damage to electrical components and reduce the lifespan of the system. The overvoltage detection levels for the 200 V and 400 V classes are approximately 410 V and 820 V, respectively.The possible cause for the overshoot in motor speed during acceleration is due to a fast acceleration time. The following solutions can be considered to resolve the issue:
Decreasing the acceleration time: Decreasing the acceleration time will reduce the speed at which the motor is accelerating, reducing the risk of overshooting the speed reference.
Enabling Stall Prevention: Stall Prevention is enabled by default, and this feature can help reduce the risk of overshooting the speed reference by monitoring the motor speed and slowing down the acceleration when necessary.
Installing a Dynamic Braking Option: Installing a dynamic braking option can help absorb the excess energy generated by the motor during acceleration, reducing the risk of overshooting the speed reference.
Tuning the control parameters: Tuning the control parameters such as gains and feedforward can help optimize the control system and reduce the risk of overshooting the speed reference.
The following are the possible solutions for the different causes of overvoltage in a drive system:
Overvoltage due to sudden drive acceleration:
Check if sudden drive acceleration triggers an overvoltage alarm.
Increase the acceleration time.
Use longer S-curve acceleration and deceleration times.
Enable the Overvoltage Suppression function (L3-11 = 1).
Lengthen the S-curve at acceleration end.
Overvoltage due to excessive braking load:
Reduce the braking torque.
Use a dynamic braking option.
Lengthen the deceleration time.
Overvoltage due to surge voltage entering from the drive input power:
Install a DC reactor.
Note: Voltage surge can result from a thyristor convertor and phase advancing capacitor using the same input power supply.
Overvoltage due to ground fault in the output circuit:
Address the ground fault in the output circuit to prevent the DC bus capacitor from overcharging.
The following are possible solutions for various causes of improper speed control in a drive system:
Ground fault in the motor wiring:
Check the motor wiring for ground faults.
Correct grounding shorts and turn the power back on.
Improper setting of Speed Search-related parameters:
Check the settings for Speed Search-related parameters.
Enable Speed Search restart function (b3-19 greater than or equal to 1 to 10).
Adjust the current level during Speed Search and the deceleration time (b3-02 and b3-03 respectively).
Perform Stationary Auto-Tuning for line-to-line resistance and then enable Speed Estimation Speed Search (b3-24 = 1).
High drive input power voltage:
Check the voltage.
Lower drive input power voltage within the limits listed in the specifications.
Incorrect wiring of the braking transistor:
Check braking transistor wiring for errors.
Properly rewire the braking resistor device.
The following are possible solutions for various causes of improper speed control in a drive system:
Disconnected or incorrectly wired PG cable:
Reconnect the cable.
Correct the wiring.
Noise interference along the PG encoder wiring:
Separate the wiring from the source of the noise (often the output lines from the drive).
Drive fails to operate due to noise interference:
Review the list of possible solutions provided for controlling noise.
Review the section on handling noise interference and check the control circuit lines, main circuit lines, and ground wiring.
Incorrectly set load inertia:
Check the load inertia settings when using KEB, overvoltage suppression, or Stall Prevention during deceleration.
Adjust the load inertia ratio in L3-25 to better match the load.
Braking function used in OLV/PM:
Connect a braking resistor.
Motor hunting:
Adjust the parameters that control hunting.
Set the gain for Hunting Prevention (n1-02).
Adjust the AFR time constant (n2-02 and n2-03).
Adjust the speed feedback detection suppression gain for PM motors (n8-45) and the time constant for pull-in current (n8-47).
CoPy Writing parameter settings (flashing) . This is not an error, but a normal process indicating that parameters are being written or updated to the drive. The process, known as flashing, is necessary for configuring the drive with the necessary settings and ensuring proper operation.
CPEr Control mode of the drive does not match . The error "CPEr Control Mode Mismatch" indicates that the control mode of the parameters to be loaded onto the drive and the control mode already set to the drive are different. This can cause issues with the operation of the drive.
To resolve the error, the control mode for the parameters to be loaded onto the drive and the control mode set to the drive need to be checked. They should be set to the same value. This can be done by using parameter A1-02 and trying again. By setting the same control mode, the mismatch error should be resolved and the drive should operate correctly.
CPyE Error writing data . The error "CPyE Error Writing Data" indicates that there was a failure in writing parameters to the drive. This can occur due to various reasons such as communication errors, power fluctuations, or hardware issues.
The possible solution to this error is to try writing the parameters again. If the issue persists, it is recommended to check the communication between the drive and the computer or device being used, as well as the power supply to the drive to ensure that there are no fluctuations. If the problem still persists, it may be a hardware issue and it is recommended to seek the assistance of a technician to diagnose and resolve the issue.
CSEr Error occurred in the copy function . The error "CSEr Copy Unit Error" indicates a hardware fault with the USB Copy Unit or the operator. This error can cause the drive to not function properly and prevent the transfer of data or parameters.
The solution to this error is to replace either the USB Copy Unit or the operator, depending on the source of the fault. If the problem persists even after replacing the hardware, it is recommended to seek assistance from a technician to diagnose and resolve the issue.
dFPS Drive models do not match. . The error "dFPS Drive Model Mismatch" indicates that the drive from which the parameters were copied and the drive you are attempting to write to are not the same model. This can cause issues with the compatibility of the parameters and the drive's operation.
To resolve the error, the model number of the drive from which the parameters were copied and the model number of the drive you are attempting to write to should be checked. The two drives should have the same model number and software version to ensure compatibility. If the drives have different model numbers or software versions, it may not be possible to transfer the parameters and a different set of parameters that are compatible with the target drive may need to be used.
End Task completed .
iFEr Communication error . The error "iFEr Communication Error" indicates that a communication error has occurred between the drive and the operator or USB Copy Unit. This can prevent the transfer of parameters or data and cause issues with the operation of the drive.
To resolve the error, the cable connection should be checked. Ensure that the cable is securely connected and not damaged. If a non-compatible cable is being used to connect the USB Copy Unit and the drive, it is recommended to use the cable that was originally packaged with the USB Copy Unit. This will ensure that the correct cable is being used and reduce the likelihood of a communication error occurring. If the problem persists, it may be necessary to seek assistance from a technician to diagnose and resolve the issue.
ndAT Model, voltage class, capacity, and/or control mode differ . The error "ndAT Model, Voltage Class, Capacity Mismatch" indicates that the drive from which the parameters were copied and the drive you are attempting to write to have different electrical specifications, capacity, control mode, or model number. This can cause issues with the compatibility of the parameters and the operation of the drive.
To resolve the error, it is important to ensure that the model numbers and specifications are the same for both drives. The drive from which the parameters were copied and the drive you are attempting to write to should have the same specifications to ensure compatibility.
If the device being used to write the parameters is blank and does not have any parameters saved on it, it is recommended to copy the parameter settings onto the USB Copy Unit or the operator. Before copying the parameters, ensure that all connections are correct. If the problem persists, it may be necessary to seek assistance from a technician to diagnose and resolve the issue.
rdEr Error reading data . The error "rdEr Error Reading Data" indicates that there was a failure while attempting to read the parameter settings from the drive. This can prevent the transfer of parameters or data and cause issues with the operation of the drive.
The solution to this error is to press and hold the READ key on the USB Copy Unit for at least one second. This will initiate the process of reading parameters from the drive. If the problem persists even after trying to read the parameters again, it is recommended to seek assistance from a technician to diagnose and resolve the issue.
rEAd Reading parameter settings (flashing) . "rEAd Reading Parameter Settings (flashing)" is not an error. It is a message displayed during the process of reading the parameter settings from the drive onto the USB Copy Unit. The message indicates that the parameters are being read and transferred from the drive to the USB Copy Unit. The process of reading parameters from the drive should take a few seconds, and once it is completed, the parameters can be written to a different drive or saved for later use. If the process is interrupted, it may be necessary to repeat the process or seek assistance from a technician.
+ Next page >>
- previous page <<