Hello,

Main power : 220 vAc

Output : 2.2 Kw

Motor circur : 10.5 Amper

Teco Smart VFD L510

Control Mode: V/F Control +Auto-torque compensation function
Range: 0.01~650.00Hz
Setting resolution
Digital input : 0.01Hz
Analog input : 0.06Hz/60Hz
Setting Keypad : Set directly with▲▼ keys or the VR (Potentiometer) on the keypad
External Input Terminlas: AVI(0/2~10V), ACI(0/4~20mA)input
Multifunction input up/down function
Frequency limit Lower and upper frequency limits
3 skip frequency settings.

Operation set
External terminals: Multi- operation-mode 2 / 3 wire selection, Jog operation

V / F curve setting: 6 fixed curve, One programmable.
Carrier frequency: 1~16KHz(default 5KHz)

Acceleration and deceleration control:
2 off Acc / dec time parameters.
4 off S curve parameters.

Multifunction input: 19 functions (refer to description on group3)
Multifunction analog output: 5 functions (refer to description on group3)
Multifunction output: 14 functions (refer to description on group3)

Main features
Overload Detection, 8 preset speeds, Auto-run, Acc/Dec, Switch (2 Stages), Main/Alt run Command select, Main/Alt
Frequency Command select, PID control, torque boost, V/F start Frequency ,Fault reset, Firemode

Display: parameter/parameter value/frequency/line speed/DC voltage/output voltage/output current/PID feedback/input and
output terminal status/Heat sink temperature/Program Version/Fault Log.
LED Status Indicator: For run/stop/forward and reverse.
Overload Protection: Integrated motor and Inverter overload protection.

Over voltage: Over 410V
Under voltage: Under 190V


Momentary Power Loss: Restart Inverter auto-restart after a momentary power loss.
Stall Prevention: Stall prevention for Acceleration/ Deceleration/ and continuous Run.
Short-circuit: output terminal Electronic Circuit Protection
Grounding Fault: Electronic Circuit Protection

10V Built in Power for an external speed potentiometer
AVI Analog voltage input, Specification : 0~10VDC/ 2-10V
ACI Analog current input, Specification : 0/4~20mA
AO Multi function analog output terminal. Maximum output 10VDC/1mA
AGND Analog ground terminal

+ Teco Contact

+ Teco L510 User manual 

+ Teco L510 Fault codes

+ Teco VFD price list

+ Teco Automation main page

++ Vfd Main page

Attention please !! All installation work of TECO drives should ONLY be performed by qualified technical personnel. Installation must always be carried out in accordance with the relevant ministry laws or regulations in force (2006/42/EC). Otomasyon AVM does not accept any responsibility for installations and individuals that violate local laws and / or other regulations (for overseas sales). If the instructions given by TECO are not followed, the device may experience problems that are not covered by the warranty. Detailed information on this subject is given in detail in the user manual. For detailed information, you can contact adress teco@otomasyonavm.com.

Write a review

Note: HTML is not translated!
Bad Good

Teco L510-203-H1F-P

  • 253.00USD

  • Ex Tax: 253.00USD

Related Products

Teco S310 1.5kw

Teco S310 1.5kw

Teco Economy  input: 220v Ac  output: 1.5 kw Ac motor drive  S310 vfd  Control M..

80.00USD Ex Tax: 80.00USD

Teco N3 JNN3-203-CS

Teco N3 JNN3-203-CS

N3 Series VFD Power : 220 Volt Motor : 2.2 kW Output :  10.5 Amper Control Mode: V/F scaler or ..

91.00USD Ex Tax: 91.00USD

Teco L510-202-H1F-P

Teco L510-202-H1F-P

Hello, Main power : 220 vAc Output : 1.5 Kw Motor circur : 7.5 Amper Teco Smart VFD L510 Control Mod..

252.00USD Ex Tax: 252.00USD

0.75 Kw -220v Derell sürücü

0.75 Kw -220v Derell sürücü

0.75 Kw -220v Derell sürücü..

102.00USD Ex Tax: 102.00USD