invt DA180 Servo Fault Code -1

INVT DA180 Servo Fault Codes 1

INVT DA180 servo drive fault and warning codes help identify problems related to the power supply, motor wiring, encoder feedback, drive electronics and mechanical load. Correctly reading the code shown on the servo drive display is the first step in identifying the cause of the fault and taking the correct action.

This section covers the DA180 warning codes AL-LT1, AL-LT2, AL-EST, AL-Pof and AL-cTE, together with the error codes Er-EEP, Er-Ec1, Er-Ec2, Er-iTE, Er-oc1, Er-oc2, Er-ou, Er-uu, Er-oL and Er-LnE.

INVT DA180 Warning Codes

AL-LT1 - Forward travel limit warning
This warning is generated when forward movement is limited or the PSL terminal is disconnected.

AL-LT2 - Reverse travel limit warning
This warning is generated when reverse movement is limited or the RVL terminal is disconnected.

AL-EST - Emergency stop warning
This warning is generated when the emergency stop circuit is activated or the EMG terminal is disconnected.

AL-Pof - Main circuit low-voltage warning
This warning is generated when the main circuit voltage falls below the required operating level.

AL-cTE - Communication abnormality warning
This warning is generated when a communication timeout or abnormal communication condition occurs while Pc.26=1.

INVT DA180 Error Codes

Er-EEP - EEPROM error
Cause: The EEPROM data is corrupted.
Solution: Replace the servo drive.

Er-Ec1 - Encoder disconnection error 1
Cause: The encoder may not be connected, the encoder connector may be loose, or one of the U, V or W phase cables may be disconnected.
Solution: Check the encoder connection and connector. Replace the encoder cable if necessary.

Er-Ec2 - Encoder error 2
Cause: Encoder A/B phases may be connected incorrectly, or one of the A, B or Z phase cables may be disconnected.
Solution: Check that the encoder phases are connected correctly. Replace the encoder cable if necessary.

Er-iTE - Current test error
Cause: The current sensor or test circuit may be faulty, or power may have been applied while the motor shaft was still moving.
Solution: Replace the drive if the current detection circuit is faulty. Do not apply power while the motor shaft is moving.

Er-oc1 - Hardware overcurrent error
Cause: The U, V and W motor phases may be connected incorrectly. Incorrect parameters, very short acceleration/deceleration times or a sudden heavy load may also cause this fault.
Solution: Check the motor phase connections. Adjust the control parameters and decrease FP0.12 if required. Increase the acceleration and deceleration times. If the load exceeds the drive capacity, use a higher-power servo drive.

Er-oc2 - Ground short-circuit error
Cause: One of the U, V or W motor phases may be short-circuited to ground.
Solution: Check and replace the motor cable if necessary. If the motor insulation is old or suspected to be damaged, test the motor insulation.

Er-ou - Overvoltage error
Cause: The mains voltage may be too high, the braking resistor may not be connected, the braking transistor may be faulty, or the acceleration/deceleration time may be too short.
Solution: Measure the mains input voltage. Check the braking resistor and its connection. Replace the drive if the braking circuit is faulty. Increase the acceleration and deceleration times if required.

Er-uu - Main DC bus undervoltage error
Cause: The mains voltage may be too low or the power relay may not have activated.
Solution: Check the mains input voltage. If the supply is normal and the fault remains, inspect or replace the servo drive.

Er-oL - Overload error
Cause: The servo system may have operated under overload for an extended period, or the load may have become excessively heavy within a short period.
Solution: Check the mechanical load. If the application exceeds the capacity of the existing motor and drive, use a higher-power servo motor and drive.

Er-LnE - Line abnormality error
Cause: The U, V and W phases of the motor cable may be connected incorrectly.
Solution: Check that the motor phases are connected to the correct terminals.

INVT DA180 Fault Code Document

+ INVT DA180 Servo Fault Codes (PDF)

Related INVT Servo Pages

+ INVT DA180 Servo Fault Code Index

+ INVT Servo Manuals and Documents

+ INVT Servo Systems

+ INVT Main Page