IC697PWR710

120/240 VAC or 125 VDC, 55W Power Supply Module (IC697PWR710/712)

This power supply module is built for IC697 systems and plugs into the leftmost slot in your rack. It supports both AC and DC inputs, making it quite flexible. Here’s what you need to know:

Key Features:

  • Works with 120/240V AC or 125V DC input.
  • Provides +5V output up to 11 amps.
  • Easily mounts into the rack.
  • Short-circuit and overcurrent protection on the 5V line.
  • Can power two racks from a single power supply.
  • Power factor correction on AC inputs, meaning you don’t need oversized wiring or breakers.

How It Works:

This module provides +5V power to your system along with the sequencing signals required for proper operation. It can be used to power one rack or two racks if your power needs stay within the limits. The connection to a second rack is made using a prewired cable (IC697CBL700/713).

Even if you lose power for a full cycle, this power supply has got you covered—it will ride through the loss and keep things running smoothly. It also has built-in protection against overcurrent and overvoltage conditions.

Dual Rack Operation:

  • +5V power is all that’s needed for the second rack.
  • The second rack shouldn’t draw more than 5.2 amps.
  • Both racks need to be close enough to be connected by the 3-foot cable.

The cable carries both power and sequencing signals, but you’ll still need separate modules for inter-rack communication and bus interfaces.

Protection Features:

  • Overvoltage Protection: If the 5V bus exceeds 6.2V, the power supply clamps down to protect the system.
  • Overcurrent Protection: Limits the current at 12 amps. If you exceed this, the voltage drops until the load is reduced.
  • Ride-Through: Can handle at least one full power cycle without losing output voltage, ensuring smooth operations.

Mounting & Field Wiring:

  • This power supply is a plug-in module, easily installed in the leftmost slot of your IC697 rack.
  • The power supply door opens easily from the top-left corner.
  • Field wiring connections are made via four terminals:
    • L1 and N for the AC or DC input.
    • Ground and overvoltage protection connections.

It’s recommended to use AWG #16 wire for power connections and AWG #12 for grounding.

Timing and Power Stability:

The power supply ensures the system stays stable during power-up and power-down sequences. The ACFAIL and SYSRESET signals handle power loss, giving the system 200 milliseconds to reset and shut down gracefully if necessary.

Technical Specs:

Input Voltage Range: 90-264V AC or 100-150V DC.

Power Output: Up to 55 watts.

+5V Output: Between 4.90V and 5.25V.

Protection Limits: 6.2V for overvoltage, 12 amps for overcurrent.

Ride-Through Time: 21 milliseconds minimum, so brief power outages won’t disrupt the system.


>> GE Fanuc IC697PWR710 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697PWR710 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."