IC697MDL740

24/48 Volt DC, 2 Amp, 16 Point Output Module

    16 output points: Four isolated groups of 4 points each
    2 amp capacity per point
    High inrush capacity: 10x rated current

The 24/48 Volt DC 2 Amp Output Module provides 16 output points divided into four isolated groups of 4 points each. Each group of four outputs is individually fused with a 10-amp fuse. The module supports a high degree of inrush current, making it suitable for a wide range of load types with such characteristics.

At the top of the module, there are LED indicators that display the ON/OFF status of each output point on the logic (PLC) side, as well as a separate LED to indicate the status of the fuse.

The module is mechanically keyed to prevent incorrect replacement with a different module type. I/O references can be configured by the user without the need for jumpers or DIP switches on the module.

Configuration is performed using the MS-DOS or Windows programming software that operates on Windows 95, Windows NT, and connects via Ethernet TCP/IP or through the SNP port. The configuration software is installed on the programming device, which can be an IBM XT, AT, PS/2, or compatible personal computer.


Output Characteristics:

The 24/48 Volt DC 2 Amp Output Module is compatible with various load devices, such as:

    Solenoids
    Motor starters
    Indicators

The output current rating is 2 amps per point. Each group of four outputs has a total current capacity of 4 amps. Each output can handle a surge current greater than its long-term rating. The repetition rate for surge currents depends on the device's current rating and duty cycle (the percentage of time the device is ON). For typical incandescent devices operating at a 50% duty cycle, the following repetition rates apply:


Steady-State Current (mA)    Repetition Rate (Hz)
0.5    5
1    1
2    0.1


Fault Mode Selection:

The output points can be configured to respond to certain operating or default conditions by assuming one of two states:

    Maintain the existing output state
    Turn outputs OFF

More detailed information can be found in the programming manual.


Fusing:

Each group of 4 outputs is protected by a 10-amp fuse. When replacing the fuse, use one of the following types:

    3AG - 10 amp, 250V, Fast Acting
    Metric 5 x 20 mm - 10 amp, 250V, Fast Acting


Mechanical Keying:

The module includes a mechanical key that prevents the inadvertent substitution of another module type in the same slot. The key fits into a specific area on the module and remains latched to the backplane when the module is removed, ensuring that only identical module types can be inserted into the slot.


Field Wiring:

The module is wired as shown. Each group of four outputs is isolated, and a wire from the power source to the power input terminals is required for each group (the power input terminals for each group are not connected inside the module). The terminal board supports wire sizes ranging from AWG #22 (0.36 mm²) to AWG #14 (2.1 mm²). Two wires of the same size can be terminated on one lug. There is enough room for a bundle of forty #14 wires to pass through the terminal board cavity. The wire bundle can be secured to the terminal board using a cable tie.


Technical Specifications:
Parameter    Details
    Rated Voltage    24 or 48 volts DC
    Outputs per Module    16 (four groups of 4 outputs each)
    Isolation    1500 volts (output to backplane), 500 volts (between groups)
    Output Voltage Range    20 to 60 volts DC
    Output Current    2 amps maximum per point, 4 amps maximum per group
    Inrush Current    20 amps maximum for 20 ms
    Output Voltage Drop    Maximum 0.8 volts (0.4 ohms)
    Response Time (On)    2 ms maximum
    Response Time (Off)    2 ms maximum
    Output Leakage Current    1 mA maximum
    Current Required from 5V Bus    0.15 amps

The module is designed to support the VME system standard, VME standard C.1.


>> GE Fanuc IC697MDL740 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697MDL740 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."