IC697CHS790

Nine Slot, Rear Mount - IC697CHS790 (9-Slot Rear-Mounted Rack)

This rack is designed for industrial use, supporting both CPU and I/O modules of the IC697 series. It offers flexibility for a wide range of applications while ensuring robust performance.


Key Features:

    Compatibility: Accepts all IC697 PLC modules.
    Mounting:
        The rear-mount version fits into a 10-inch (254 mm) deep enclosure. No fans are typically required.
        A front-mount version fits into a standard 19-inch (480 mm) rack.
    Power Supply: It supports plug-in AC or DC IC697 power supplies.
    Dual Rack Operation: You can run two racks with a single power supply by using a Power Supply Extension Cable (IC697CBL700).


Functions:

    Rack Dimensions:
        Nine-Slot Rack (IC697CHS790): 11.15 inches (283mm) height, 19 inches (483mm) width, and 7.5 inches (190mm) depth.
        Slot Widths: Each slot is 1.6 inches wide, except for the power supply slot, which is 2.4 inches wide.
    Interconnection for Extended I/O: Two racks can be interconnected to share a power supply, allowing more extensive I/O configurations. The Power Supply Extension Cable ensures proper power distribution between the racks.


Rack Mounting Requirements:

To ensure proper airflow for cooling, adequate space must be left around the rack during installation. For environments where heat buildup is an issue, a Rack Fan Assembly is available:

    IC697ACC721: For 120 VAC power.
    IC697ACC724: For 240 VAC power.
    IC697ACC744: For 24 VDC power.


I/O Connector and Wiring:

This rack accommodates high-density I/O modules with a detachable field wiring terminal board. Each I/O module can handle up to #14 AWG (2.10mm²) wires. The wiring bundle can be routed through the bottom and secured using a cleat to avoid movement.


Mechanical Keying:

IC697 I/O modules are mechanically keyed to prevent incorrect insertion. A unique key for each module type ensures that only the correct module can be installed in each slot. If you need to change the module’s position, the key can be easily removed and reinserted.


Power Supply Extension Cable:

One power supply can support two racks, provided the second rack requires 5 volts at 5.2 amperes or less. The Power Supply Extension Cable (1 meter) connects to the backplane via a 9-pin D-type connector. Ensure that 6 inches (152.4mm) of clearance is left on the left side for cable access.


Slot Addressing and Rack Numbering:

The IC697 PLC system allows the configuration of I/O points for each module without DIP switches or jumpers. The configuration is handled by the MS-DOS or Windows programming software.
Each rack is assigned a unique number (0-7), with Rack 0 always reserved for the CPU. The rack number is set using binary-encoded jumpers located behind the power supply.



>> GE Fanuc IC697CHS790 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: IC697CHS790 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."