IC697ACC715

VME Option Kit (IC697ACC715)

The VME Option Kit (IC697ACC715) allows you to add a J2 VME backplane (which has P2 connectors) to an IC697 PLC rack. This guide provides the necessary information for the installation of the kit.


Contents of the VME Option Kit

    Connector jumper: 6 pieces
    M2.5 threaded strip: 2 pieces
    Aluminum spacer: 4 pieces
    VME slot filler: 4 pieces
    Phillips screws (M2.5 x 8): 24 pieces
    Spring lock washers: 24 pieces
    Hex nuts (M2.5): 12 pieces
    Power cable: 1 piece
    Ribbon cable connector mounting bracket: 6 pieces
    User's Guide to Integration of 3rd Party VME Modules: 1 piece

    Note: This kit does not contain a J2 backplane. It must be purchased from a third-party supplier.

Required Tools and Components

    Phillips head screwdriver
    A five-slot or nine-slot IC697 rack (IC697CHS750, IC697CHS790, or IC697CHS791)
    A J2 backplane with P2 connectors
    Any VME module with both a P1 and P2 connector
    User-supplied rack mounting hardware (e.g., #10-32 or #12-28 screws, 1 1/4 inch long)

Installation Steps

    Unpack and verify all items in the kit using the provided parts list.
    Place the selected rack on its side, ensuring it is straight and level.
    Locate the slot in the rear bottom rail of the rack and slide the provided threaded strip into the slot. For five-slot racks, trim any excess length by snapping the strip after the last threaded hole.
    Repeat the process for the center rail of the rack, inserting the second threaded strip. Reinstall the rack side plate if removed.
    Insert the standard VME module into the rack slot that will align with the J2 backplane.
    Gently plug the middle connector of the J2 backplane into the P2 connector of the VME module, ensuring correct alignment.
    Secure the J2 backplane to the threaded strips using the screws and lock washers from the kit.
    Connect the provided power cable to the nine-pin connector on the side of the rack and attach the leads to the J2 backplane’s saddle clamps (ensure correct polarity: +5V to +5V and GND to GND).
    If using a panel mount rack (IC697CHS790 or IC697CHS750), use the provided spacers to prevent wire-wrap pins from contacting the mounting panel.
    Jumper connectors are provided for configuring any slot (except slot 1) to function as a normal VME slot. Place four jumpers on the corresponding pins in the backplane.
    Blank Slot Fillers (IC697ACC720) can be used to cover any open spaces between VME modules and other modules in the rack.

J2 Installation Alternative

Six ribbon cable mounting brackets are included for use as an alternative to mounting the J2 backplane. The ribbon cable with a J2 connector can be mounted on the bracket, which provides external I/O connections to a VME module in the rack.

    Mount the J2 connector and secure it to the bracket using screws, lock washers, and hex nuts.
    Install the bracket loosely at the selected slot, align it with the VME module, and tighten the mounting screws.

This VME Option Kit is designed to extend the functionality of the IC697 PLC system by adding support for VME modules, ensuring a flexible solution for various industrial applications.

>> GE Fanuc IC697ACC715 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697ACC715 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."