IC694MDL931

IC694MDL931 Isolated Relay Output Module: High-Current Capacity and Flexible Control

The IC694MDL931 is an 8 Amp isolated relay output module that provides four normally-closed (N.C.) and four Form C relay circuits for controlling user-supplied output loads. Each circuit has a switching capacity of 8 Amps. Every relay is isolated from the others, and each relay has its own common power output terminal. This module can control a wide range of devices, including motor starters, solenoids, and indicators. The AC or DC power required to operate the connected field devices must be supplied by the user.

Each output point has a numbered LED to indicate its ON/OFF status. There are no fuses on the module. The red bands on the label signify that the MDL931 is a high-voltage module. This module can be installed in any I/O slot within an RX3i system.

Technical Specifications

    Rated Voltage: 24V DC, 120/240V AC, 50/60 Hz (nominal, see table below for exceptions)
    Output Voltage Range: 5 to 30V DC, 5 to 250V AC, 50/60 Hz
    Outputs per Module: 8 isolated outputs
    Isolation:
        250 VAC continuous (Field to Backplane and Frame Ground)
        1500 VAC for 1 minute (Field to Backplane and Frame Ground)
        250 VAC continuous (Point to Point); 1500 VAC for 1 minute

Maximum Load:
        8 Amps resistive load per output
        Maximum of 20 Amps per module for UL installations
        Maximum load depends on ambient temperature
    Minimum Load: 10 mA
    Inrush Current: 8 Amps (maximum for one cycle)
    On/Off Response Time: Maximum 15 ms for both ON and OFF
    Output Leakage Current: Maximum 1 mA at 250V AC (at 25°C)
    Power Consumption:
        6 mA from the 5V bus on the backplane (all outputs ON)
        110 mA from the 24V relay bus on the backplane (all outputs ON)

Load Current vs. Temperature

Maximum load current capacity is affected by the ambient temperature. For example:

    At 10°C, total load current is 32 Amps
    At 35°C, each point can handle 6 Amps
    At 45°C, each point can handle 4 Amps

Field Wiring

The terminal connections for the IC694MDL931 module are as follows:

    Terminals 1-2: Output 1 and common
    Terminals 3-4: Output 2 and common
    Terminals 5-6: Output 3 and common
    Terminals 7-8: Output 4 and common
    Terminals 9-11: Normally-closed Output 5 (N.C.), common, and normally-open Output 5 (N.O.)
    Terminals 12-14: Normally-closed Output 6 (N.C.), common, and normally-open Output 6 (N.O.)
    Terminals 15-17: Normally-closed Output 7 (N.C.), common, and normally-open Output 7 (N.O.)
    Terminals 18-20: Normally-closed Output 8 (N.C.), common, and normally-open Output 8 (N.O.)

Recommendations

The IC694MDL931 module offers a high-current capacity and flexible control solution, capable of handling up to 8 Amps per output. It is ideal for controlling various devices in industrial automation systems, such as motor starters, solenoids, and indicators. The combination of normally-closed (N.C.) and Form C relay circuits provides flexibility for different circuit requirements. This module is a reliable choice for high-voltage applications, offering robust and isolated output control.

>> IC694MDL931 Output modules User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC694MDL931 Output modules and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."